DOI QR코드

DOI QR Code

Assessment of portable traveling pluviator to prepare reconstituted sand specimens

  • Dave, Trudeep N. (Dept. of Civil Engg., IIT Bombay) ;
  • Dasaka, S.M. (Dept. of Civil Engg., IIT Bombay)
  • 투고 : 2012.01.16
  • 심사 : 2012.03.21
  • 발행 : 2012.06.25

초록

Air pluviation method is widely adopted for preparation of large, uniform and repeatable sand beds of desired densities for laboratory studies to simulate in-situ conditions and obtain test results which are highly reliable. This paper presents details of a portable traveling pluviator recently developed for model sand bed preparation. The pluviator essentially consisted of a hopper, orifice plates for varying deposition intensity, combination of flexible and rigid tubes for smooth travel of material, and a set of diffuser sieves to obtain uniformity of pluviated sand bed. It was observed that sand beds of lower relative density can be achieved by controlling height of fall, whereas, denser sand beds could be obtained by controlling deposition intensity. Uniformity of pluviated sand beds was evaluated using cone penetration test and at lower relative densities minor variation in density was observed with depth. With increase in relative density of sand bed higher repeatability of uniform pluviation was achieved.

키워드

참고문헌

  1. Abbireddy, C.O.R. (2009), "Particle form and its impact on packing and shear behavior of particulate materials", PhD Thesis, School of Civil Engineering and the Environment, University of Southampton.
  2. ASTM Standard D4253-06 (2006), "Standard test methods for maximum index density and unit weight of soils using a vibratory table", Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA.
  3. ASTM Standard D4254-00 (2006), "Standard test methods for minimum index density and unit weight of soils and calculation of relative density", Annual Book of ASTM Standards, ASTM International, West Conshohocken, PA.
  4. Bolton, M.D., Gui, M.W., Garnier, J., Corte, J.F., Bagge, G., Laue, J. and Renzi, R. (1999), "Centrifuge cone penetration tests in sand", Geotechnique, 49(4), 543-552. https://doi.org/10.1680/geot.1999.49.4.543
  5. Butterfield, R. and Andrawes, K.Z. (1970), "An air activated and spreader for forming uniform sand bed", Geotechnique, 20(1), 97-100. https://doi.org/10.1680/geot.1970.20.1.97
  6. Chen, H.-T., Lee, C. and Chen, H. (1998), "The traveling pluviation apparatus for sand specimen preparation", Centrifuge 98, Kimura, Kusakabe, and Takemura, Eds., Vol. 1, Balkema, Rotterdam, pp. 143-148.
  7. Clayton, C.R.I., Bica, A.V.D. and Moore, S.R. (1994), "A resin impregnation technique for determination of the density variations in completed specimens of dry cohesionless soils", Geotechnique, 44(1), 165-173. https://doi.org/10.1680/geot.1994.44.1.165
  8. Cresswell, A, Barton, M.E. and Brown, R. (1999), "Determining the maximum unit weight of sands by pluviation", Geotech. Test. J., 22(4), 324-328. https://doi.org/10.1520/GTJ11245J
  9. Dupla, J.C., Canau, J. and Gouvenot, D. (2004), "An advanced experimental set-up for studying a monodirectional grout injection process", Ground Improvement, 8(3), 91-99. https://doi.org/10.1680/grim.2004.8.3.91
  10. Fretti, C., Lo Presti, D.C.E. and Pedroni, S. (1995), "A pluvial deposition method to reconstitute specimens well-graded sand", Geotech. Test. J., 18(2), 292-298. https://doi.org/10.1520/GTJ10330J
  11. Hsu, H.H. and Hwang, A.B. (1999), "Calibration of cone penetration test in sand", Proc. Natl. Sci. Counc. ROC(A), 23(5), 579-590.
  12. Kildalen, S. and Stenhamar, P. (1977), "NGI laboratory sand rainer", Internal Report 51505-15, Norwegian Geotechnical Institute.
  13. Kolbuszewski, J.J. (1948), "An experimental study of the maximum and minimum porosities of sands", Proceedings of the Second International Conference of Soil Mechanics and Foundation Engineering, Rotterdam, 21-30 June, 1, 158-165.
  14. Kolbuszewski, J.J. and Jones, R.H. (1961), "The preparation of sand samples for laboratory testing", Proceedings of the Midland Soil Mechanics & Foundation Engineering Society, 4, 107-123.
  15. Kuerbis, R. and Vaid, Y.P. (1988), "Sand sample preparation - The slurry deposition method, Soils Found., 8(4), 107-118.
  16. Lagioia, R., Sanzeni, A. and Colleselli, F. (2006), "Air, water and vacuum pluviation of sand specimens for the triaxial apparatus", Soils Found., 46(1), 61-67. https://doi.org/10.3208/sandf.46.61
  17. Lo Presti, D.C.F., Pedroni, S. and Crippa, V. (1992), "Maximum dry density of cohesionless soils by pluviation and by ASTM D 4253-83: A Comparative Study", Geotech. Test. J., 15(2), 180-189. https://doi.org/10.1520/GTJ10239J
  18. Lo Presti, D.C.F., Berardi, R., Pedroni, S. and Crippa, V. (1993), "A new traveling sand pluviator to reconstitute specimens of well-graded silty sands", Geotech. Test. J., 16(1), 18-26. https://doi.org/10.1520/GTJ10263J
  19. Muira, S. and Toki, S. (1982), "A Sample preparation method and its effect on static and cyclic deformation strength properties of sand", Soils Found., 22(1), 61-77. https://doi.org/10.3208/sandf1972.22.61
  20. Mulilis, J.P., Chan, C.K. and Seed, H.B. (1975), "The effect of method of sample preparation on the cyclic stress-strain behaviour of sand", EERC Report 75-17, University of California, Berkeley.
  21. Rad, N.S. and Tumay, M.T. (1987), "Factors affecting sand specimen preparation by raining", Geotech. Test. J., 10(1), 31-37. https://doi.org/10.1520/GTJ10136J
  22. Saussus, D.R., Frost, D. and Ashmawy, A.K. (2000), "Variation in membrane contact patterns of reconstituted sand samples", Geotech. Test. J., 23(4), 522-531. https://doi.org/10.1520/GTJ11072J
  23. Stuit, H.G. (1995), "Sand in the geotechnical centrifuge", Ph.D. thesis, Technische Universiteit Delft, Netherlands.
  24. Tatsuoka, F., Maramatsu, M. and Sasaki, T. (1982), "Cyclic undrain stress-strain behaviour of dense sand by torsional simple shear tests", Soils Found., 22(2), 55-70. https://doi.org/10.3208/sandf1972.22.2_55
  25. Vaid, Y.P. and Negussey, D. (1988), "Preparation of reconstituted sand specimens", Advanced Triaxial Testing of Soil and Rock, ASTM STP 977, ASTM International, West Conshohocken, PA, pp. 405-417.
  26. Walker, B.P. and Whitaker, T. (1967), "An apparatus for forming uniform beds of sands for model foundation tests", Geotechnique, 17(2), 161-167. https://doi.org/10.1680/geot.1967.17.2.161
  27. Wang, S., Luna, R. and Stephenson, R.W. (2011), "A slurry consolidation approach to reconstitute low-plasticity silt specimens for laboratory triaxial testing", Geotech. Test. J., 34(4), 1-9.
  28. Zhao, Y., Gafar, K., Elshafie, M.Z.E.B., Deeks, A.D., Knappett, J.A. and Madabushi, S.P.G. (2006), "Calibration and use of new automatic sand pourer", Sixth International Conference on Physical Modeling in Geotechnics, Hong Kong, 4-6 August, Taylor & Francis, London, pp. 265-270.

피인용 문헌

  1. Experimental investigation of free head model piles under lateral load in homogenous and layered sand vol.9, pp.4, 2015, https://doi.org/10.1179/1939787914Y.0000000078
  2. Development of a Mechanized Traveling Pluviator to Prepare Reconstituted Uniform Sand Specimens vol.28, pp.2, 2016, https://doi.org/10.1061/(ASCE)MT.1943-5533.0001396
  3. Transition of earth pressure on rigid retaining walls subjected to surcharge loading vol.6, pp.4, 2012, https://doi.org/10.3328/IJGE.2012.06.04.427-435
  4. Comparison Analysis of Bearing Capacity Approaches for the Strip Footing on Layered Soils vol.42, pp.9, 2017, https://doi.org/10.1007/s13369-017-2490-6
  5. Preparation of Uniform Sand Specimens Using Stationary Pluviation and Vibratory Methods vol.34, pp.6, 2016, https://doi.org/10.1007/s10706-016-0064-0
  6. Uplift resistance of belled and multi-belled piles in loose sand vol.109, 2017, https://doi.org/10.1016/j.measurement.2017.06.001
  7. Effect of boundary conditions on earth pressure reduction using EPS Geofoam vol.2, pp.66, 2016, https://doi.org/10.3208/jgssp.IND-34
  8. Optimization and Parametrical Investigation to Assess the Reconstitution of Different Types of Indian Sand Using Portable Travelling Pluviator vol.34, pp.1, 2016, https://doi.org/10.1007/s10706-015-9928-y
  9. Assessment of Air Pluviation Using Stationary and Movable Pluviators vol.29, pp.5, 2017, https://doi.org/10.1061/(ASCE)MT.1943-5533.0001798
  10. Comparison between Two Different Pluviation Setups of Sand Specimens vol.29, pp.10, 2017, https://doi.org/10.1061/(ASCE)MT.1943-5533.0001985
  11. 砂土地基中摩擦型能量桩群桩热力学特性研究 vol.19, pp.8, 2018, https://doi.org/10.1631/jzus.A1700460
  12. 繰返し荷重振幅がジオグリッドで補強された骨材層の変形に及ぼす影響 vol.32, pp.0, 2017, https://doi.org/10.5030/jcigsjournal.32.25
  13. Effects of preparation methods on inherent fabric anisotropy and packing density of reconstituted sand vol.5, pp.1, 2012, https://doi.org/10.1080/23311916.2018.1533363
  14. Experimental Analysis of Strength and Deformation Behavior of Soils Reinforced with Building-Derived Materials vol.50, pp.3, 2020, https://doi.org/10.1007/s40098-019-00367-5
  15. Synthesis and characterisation of zinc oxide catalyst and its composite with polymer additives vol.870, pp.None, 2012, https://doi.org/10.1088/1757-899x/870/1/012023
  16. Design, Manufacturing and Testing of Biaxial Mechanical Travelling Pluviator vol.870, pp.None, 2012, https://doi.org/10.1088/1757-899x/870/1/012071
  17. Using grain size to predict engineering properties of natural sands in Pakistan vol.22, pp.2, 2012, https://doi.org/10.12989/gae.2020.22.2.165
  18. Effect of Perforated Plates on the Relative Density of Uniformly Graded Reconstituted Sands Using Air Pluviation Method vol.8, pp.4, 2012, https://doi.org/10.1007/s40515-021-00150-1