DOI QR코드

DOI QR Code

Factor of safety in limit analysis of slopes

  • Florkiewicz, Antoni (Department of Civil and Environmental Engineering, Poznan University of Technology) ;
  • Kubzdela, Albert (Department of Civil and Environmental Engineering, Poznan University of Technology)
  • 투고 : 2012.11.29
  • 심사 : 2013.05.08
  • 발행 : 2013.10.25

초록

The factor of safety is the most common measure of the safety margin for slopes. When the traditionally defined factor is used in kinematic approach of limit analysis, calculations can become elaborate, and iterative methods have to be used. To avoid this inconvenience, the safety factor was defined in terms of the work rates that are part of the work balance equation used in limit analysis. It was demonstrated for two simple slopes that the safety factors calculated according to the new definition fall close to those calculated using the traditional definition. Statistical analysis was carried out to find out whether, given normal distribution of the strength parameters, the distribution of the safety factor can be approximated with a well-defined probability density function. Knowing this function would make it convenient to calculate the probability of failure. The results indicated that the normal distribution could be used for low internal friction angle (up to about $16^{\circ}$) and the Johnson distribution could be used for larger angles ${\phi}$. The data limited to two simple slopes, however, does not allow assuming these distributions a priori for other slopes.

키워드

참고문헌

  1. Bell, J.M. (1966), "Dimensionless parameters for homogeneous earth slopes", J. Soil Mech. Found. Div., Am. Soc. Civ. Eng., 92(5), 51-65.
  2. Christian, J.T., Ladd, C.C. and Baecher, G. (1994), "Reliability applied to slope stability analysis", J. Geotech. Eng., 120(12), 2180-2207. https://doi.org/10.1061/(ASCE)0733-9410(1994)120:12(2180)
  3. Derski, W., Izbicki, R., Kisiel, I. and Mroz, Z. (1988), Rock and Soil Mechanics. PWN, Warszawa.
  4. Izbicki, R.J. (1983), "Application of limit analysis method in stability of slopes", Archiwum Hydrotechniki, 29(3), 275-296. [in Polish]
  5. Karal, K. (1977), "Application of energy method", J. Geotech. Eng. Div., 103(5), 381-397.
  6. Klar, A., Aharonov, E., Kalderon-Asael, B. and Katz, O. (2011), "Analytical and observational relations between landslide volume and surface area", J. Geophys. Res., 116(F2), F02001, AGU.
  7. Lambe, T.W. and Whitman, R.V. (1968), Soil Mechanics, Wiley, New York.
  8. Michalowski, R.L. (1989), "Three-dimensional analysis of locally loaded slopes", Geotech., 39(1), 27-38. https://doi.org/10.1680/geot.1989.39.1.27
  9. Michalowski, R.L. (2002), "Stability charts for uniform slopes", J. Geotech. Geoenv. Eng., 128(4), 351-355. https://doi.org/10.1061/(ASCE)1090-0241(2002)128:4(351)
  10. Michalowski, R.L. (2010), "Limit analysis and stability charts for 3D slope failures", J. Geotech. Geoenv. Eng., 136(4), 583-593. https://doi.org/10.1061/(ASCE)GT.1943-5606.0000251
  11. Taylor, D.W. (1948), Fundamentals of Soil Mechanics, Wiley, New York.

피인용 문헌

  1. Limit analysis of ground anchor forces vol.170, pp.2, 2017, https://doi.org/10.1680/jgeen.16.00056
  2. A rheological model to simulate the shear creep behavior of rockfills considering the influence of stress states pp.1861-1133, 2018, https://doi.org/10.1007/s11440-018-0716-8
  3. Influence of undercut and surface crack on the stability of a vertical escarpment vol.12, pp.6, 2013, https://doi.org/10.12989/gae.2017.12.6.965
  4. A strain hardening model for the stress-path-dependent shear behavior of rockfills vol.13, pp.5, 2013, https://doi.org/10.12989/gae.2017.13.5.743
  5. Pseudo-static stability analysis of wedges based on the nonlinear Barton-Bandis failure criterion vol.20, pp.4, 2013, https://doi.org/10.12989/gae.2020.20.4.287
  6. Time-variant failure probability of critical slopes under strong rainfall hazard including mitigation effects vol.16, pp.10, 2020, https://doi.org/10.1080/15732479.2020.1712736
  7. Strain-based stability analysis of locally loaded slopes under variable conditions vol.23, pp.3, 2013, https://doi.org/10.12989/gae.2020.23.3.289