분산법이 무전해 Ni-CNT 복합도금막 형성에 미치는 영향

Effect of Dispersion Method on Formation of Electroless Ni-CNT Coatings

  • 배규식 (수원대학교 전자재료공학과)
  • Bae, KyooSik (Dept. of Electronic Materials Engineering, The University of Suwon)
  • 투고 : 2014.09.02
  • 심사 : 2014.09.22
  • 발행 : 2014.09.30

초록

Ni-CNT(Carbon Nanotubes) composite coating is often used for the surface treatment of mechanical/electronic devices to improve the properties of the Ni coating. For the Ni-CNT coating, the dispersion of CNT fibers is a critical process. In this study, ultrasonic treatment instead of the conventional ball milling was attempted as a dispersion method for the electroless Ni-CNT coating. SEM-EDX analysis was performed and contact angle, sheet resistance, and micro-hardness were measured. Results showed that the ultrasonic treatment was comparable to the ball milling, as a dispersion method, but the difference was negligible. However, combined ball milling and ultrasonic treatment(double treatment) showed much improved micro-hardness value, above 350Hv(close to the value obtained by the Ni-CNT electroplating). In addition, electroless Ni-CNT(double-treated) coatings formed on the thin Ni film deposited by the electroless plating(double coating) showed better mechanical properties. Thus, double treatment and double coating are suggested as an improved electroless Ni-CNT coating method.

키워드

참고문헌

  1. Nabeen K. Shrestha, Dambar B. Hamal, Tetsuo Saji, "Composite plating of Ni-P-$Al_2O_3$ in two steps and its anti-wear performance" J.of Surface and Coatings Technology, Vol.183, pp.247-253, 2004. https://doi.org/10.1016/j.surfcoat.2003.08.085
  2. K.H. Hou, M.D. Ger, L.M. Wang, S.T. Ke, "The wear behaviour of electro-codeposited Ni-SiC Composites" J. of wear Vol. 253, pp. 994-1003. 2002 https://doi.org/10.1016/S0043-1648(02)00222-3
  3. F. Hu, K.C. Chan, "Deposition behaviour and morphology of Ni-SiC electro-composites under triangular waveform" J. of Applied Surface Science, Vol. 243, pp. 251-258, 2005 https://doi.org/10.1016/j.apsusc.2004.09.068
  4. Wun-Hsing Lee, Sen-Cheh Tang, Kung-Cheng Chung, "Effects of direct current and pulse-plating on the co-deposition of nickel and nanometer diamond powder", J. of Surface and Coatings Technology, Vol. 120, pp. 607-611, 1999.
  5. Y.S. Jeon, J.Y. Byun, T.S. Oh "Electrodepositionand mechanical properties of Ni-carbon nanotube nanocomposite coatings J.of Physics and Chemistry of Solids, Vol. 2, pp1-4, 2007
  6. Sung-Kyu KIM. Tae-Sung OH, "Electrodeposition behavior and characterisitics of Ni-carbon nanotube composite coatings", Trans. Nofferrous Met. Soc. China, Vol.21, pp.s68-s72, 2011. https://doi.org/10.1016/S1003-6326(11)61063-7
  7. Susumu Arai, Morinobu Endo, Norio Kaneko, "Ni-deposited multi-waalled carbon nanotubes by electrodeposition" J. of Carbon, Vol. 42, pp. 641-644, 2004. https://doi.org/10.1016/j.carbon.2003.12.084
  8. Young Hoon Cheon, Kyoo Sik Bae, "Effect of particle dispersion on physical properties of Ni-CNT composite coatings", J. of the Semiconductor & Display Technology, Vol. 10, No. 2, pp.91-95, 2011
  9. KyooSik Bae, "Characteristics of Ni-carbon nanotube composite coatings with the CNT content", J. of the Semiconductor & Display Technology, Vol. 12, No. 3, pp.7-12, 2013
  10. F. Deng, X. Chen, W. Chen, and W. Li, "Electroless plating Ni-P matrix composite coating reinforced by carbon nanotubes", Trans. Nonferrous Met. Sci. China, Vol. 14, pp.681-685. 2004
  11. A. Azrebidaki, S.-R. Allahkaram,"Effect of surfactant on the fabrication and characterization of Ni-P-CNT composite coatings", J. of Alloys and Compounds, Vol. 509, pp.1836-1840, 2011. https://doi.org/10.1016/j.jallcom.2010.10.057
  12. M. Alishani, S.-M. Monirvaghefi, A. Saatchi, S.-M Hosseneini, "The effect of carbon nanotubes on the corrosion and tribological behavior of elecroless Ni-P-CNT compositecoating", Appl. Surf. Sci., Vol.258, pp.2439-2446, 2012. https://doi.org/10.1016/j.apsusc.2011.10.067
  13. B. Abbasipour, S.-M. Monirbaghefi, B. Niroumand, "Electroless Ni-P-CNT coating on aluminum powder", Met. Mater. Int., Vol.18, 1015-1021, 2012 https://doi.org/10.1007/s12540-012-6014-3