DOI QR코드

DOI QR Code

Soil and ribbed concrete slab interface modeling using large shear box and 3D FEM

  • Qian, Jian-Gu (Department of Geotechnical Engineering, Tongji University) ;
  • Gao, Qian (Department of Geotechnical Engineering, Tongji University) ;
  • Xue, Jian-feng (School of Engineering and IT, Federation University) ;
  • Chen, Hong-Wei (Department of Underground Structure & Geotechnical Engineering, East China Architecture Design & Research Institute Co., Ltd.) ;
  • Huang, Mao-Song (Department of Geotechnical Engineering, Tongji University)
  • 투고 : 2015.12.16
  • 심사 : 2016.10.25
  • 발행 : 2017.02.25

초록

Cast in situ and grouted concrete helical piles with 150-200 mm diameter half cylindrical ribs have become an economical and effective choice in Shanghai, China for uplift piles in deep soft soils. Though this type of pile has been successful used in practice, the reinforcing mechanism and the contribution of the ribs to the total resistance is not clear, and there is no clear guideline for the design of such piles. To study the inclusion of ribs to the contribution of shear resistance, the shear behaviour between silty sand and concrete slabs with parallel ribs at different spacing and angles were tested in a large direct shear box ($600mm{\times}400mm{\times}200mm$). The front panels of the shear box are detachable to observe the soil deformation after the test. The tests were modelled with three-dimensional finite element method in ABAQUS. It was found that, passive zones can be developed ahead of the ribs to form undulated failure surfaces. The shear resistance and failure mode are affected by the ratio of rib spacing to rib diameter. Based on the shape and continuity of the failure zones at the interface, the failure modes at the interface can be classified as "punching", "local" or "general" shear failure respectively. With the inclusion of the ribs, the pull out resistance can increase up to 17%. The optimum rib spacing to rib diameter ratio was found to be around 7 based on the observed experimental results and the numerical modelling.

키워드

과제정보

연구 과제 주관 기관 : Shanghai Science and Technology Committee

참고문헌

  1. Abbasov, P.A. and Kovalevskii, A.A. (1984), "Behavior of piles with ribbed surfaces in sand soil", Soil Mech. Found. Eng., 21(2), 69-75. https://doi.org/10.1007/BF01710704
  2. Abdelghany, Y. and El Naggar, H. (2011), "Steel Fibers Reinforced Grouted and Fiber Reinforced Polymer Helical Screw Piles-A New Dimension for Deep Foundations Seismic Performance", In: Geo-Frontiers 2011: Advances in Geotechnical Engineering, (J. Han and D.E. Alzamora Eds.), ASCE, Geotechnical Special Publication No. 211, Reston, VA, USA, pp. 103-112.
  3. Chinese Standard (2003), GB/T 50081-200200; Standard for test method of mechanical properties on ordinary concrete.
  4. Clemence, S.P., Crouch, L.K. and Stephenson, R.W. (1994), "Prediction of uplift capacity for helical anchors in sand", Proceedings of the 2nd Geotechnical Engineering Conference, Cairo, Egypt, January, Volume I, pp. 332-343.
  5. Clough, G.W. and Duncan, J.M. (1969), "Finite element analyses of Port Allen and Old River Locks", Army Engineer Waterways Experiment Station, Report No. TE-69-3; Vicksburg, MS, USA.
  6. Clough, G.W. and Duncan, J.M. (1971), "Finite element analyses of retaining wall behaviour", J. Soil Mech. Found. Div., ASCE, 97(SM12), 1657-1673.
  7. Coyle, H.M. and Sulaiman, I. (1967), "Skin friction for steel piles in sand", J. Soil Mech. Found. Div., 93(6), 261-270.
  8. Desai, C.S. and Ma, Y. (1992), "Modeling of joints and interfaces using the disturbed-state concept", Int. J. Numer. Anal. Meth. Geomech., 16(9), 623-653. https://doi.org/10.1002/nag.1610160903
  9. Desai, C.S. (1985), "Cyclic testing and modeling of interfaces", J. Geotech. Eng, ASCE, 111(GT6), 793-815. https://doi.org/10.1061/(ASCE)0733-9410(1985)111:6(793)
  10. Dove, J.E. and Jarrett, J.B. (2002), "Behavior of dilative sand interfaces in a geotribology framework", J. Geotech. Geoenviron. Eng., 128(1), 25-37. https://doi.org/10.1061/(ASCE)1090-0241(2002)128:1(25)
  11. Duncan, J.M. and Chang, C.Y. (1970), "Nonlinear analysis of stress and strain in soils", J. Soil Mech. Found. Div., ASCE, 96(SM5), 1629-1653.
  12. Elsherbiny, Z.H. and El Naggar, M.H. (2013), "Axial compressive capacity of helical piles from field tests and numerical study", Can. Geotech. J., 50(12), 1191-1203. https://doi.org/10.1139/cgj-2012-0487
  13. Esterhuizen, J.J.B., Filz, G.M. and Duncan, J.M. (2001), "Constitutive behaviour of geosynthetic interfaces", J. Geotech. Geoenviron. Eng., ASCE, 127(10), 834-840. https://doi.org/10.1061/(ASCE)1090-0241(2001)127:10(834)
  14. Gennaro, V.D. and Frank, R. (2002), "Elasto-plastic analysis of the interface behavior between granular media and structure", Comput. Geotech., 29(7), 547-572. https://doi.org/10.1016/S0266-352X(02)00010-1
  15. Ghaly, A., Hanna, A. and Hanna, M. (1991), "Uplift Behavior of Screw Anchors in Sand. I: Dry Sand", J. Geotech. Engrg., 117(5), 773-793. https://doi.org/10.1061/(ASCE)0733-9410(1991)117:5(773)
  16. Goodman, R.E., Taylor, R.L. and Brekke, T.L. (1968), "Model for mechanics of jointed rock", J. Soil Mech. Found. Div., 94(SM3), 637-659.
  17. Gomez, J.E. and Ebeling, R.M. (1999), "Development of an Improved Numerical Model for Concrete-to-Soil Interfaces in Soil-Structure Interaction Analyses", US Army Corps of Engineers, Technical Report ITL-99-1.
  18. Gu, X.M., Seidel, J.P. and Haberfield, C.M. (2003), "Direct shear test of sandstone concrete joints", Int. J. Geomech., 3(1), 21-33. https://doi.org/10.1061/(ASCE)1532-3641(2003)3:1(21)
  19. Guo, Y. and Yu, X.B. (2016), "Design and analyses of open-ended pipe piles in cohesionless soils", Front. Struct. Civ. Eng., 10(1), 22-29. https://doi.org/10.1007/s11709-016-0314-5
  20. Hossain, Md.Z. (2010), "A study on thin cementitious composite (TCC) materials for soil reinforcement applications", Australian J. Agri. Eng., 1(4), 153-159.
  21. Hossain, M.A. and Yin, J.H. (2014), "Behavior of a pressure-grouted soil-cement interface in direct shear tests", Int. J. Geomech., 14(1), 101-109. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000301
  22. Houlsby, G.T. (1991), "How the dilatancy of soils affects their behaviour", Proceedings of the 10th European Conference on Soil Mechanics and Foundation Engineering, Florence, Italy, May.
  23. Hryciw, R.D. and Irsyam, M. (1990), "Shear zone characterization in sands by carbowax impregnation", Geotech. Test. J., 13(1), 49-52. https://doi.org/10.1520/GTJ10146J
  24. Hryciw, R.D. and Irsyam, M. (1993), "Behavior of sand particles around rigid ribbed inclusions during shear", Soils Found., 33(3), 1-13. https://doi.org/10.3208/sandf1972.33.3_1
  25. Hu, L.M. and Pu, J.L. (2004), "Testing and modeling of soil-structure interface", J. Geotech. Geoenviron. Eng. ASCE, 130(8), 851-860. https://doi.org/10.1061/(ASCE)1090-0241(2004)130:8(851)
  26. Huang, M.S., Qian, J.G. and Zhang, C.R. (2013), "Performance and analysis of non-conventional uplift piles in soft ground", International Symposium on Advances in Foundation Engineering, Singapore, December.
  27. Institution of Civil Engineers (2007), ICE specification for piling and embedded retaining walls, Thomas Telford, London, UK.
  28. Irsyam, M. and Hryciw, R.D. (1991), "Friction and passive resistance in soil reinforced by plane ribbed inclusions", Geotechnique, 41(4), 485-498. https://doi.org/10.1680/geot.1991.41.4.485
  29. Iskander, M.G. and Hassan, M. (1998), "State of the practice review: FRP composite piling", J. Compos. Construct., ASCE, 2(3), 116-120. https://doi.org/10.1061/(ASCE)1090-0268(1998)2:3(116)
  30. Juran, I. and Komornik, U. (2006), "Behavior of fiber-reinforced polymer composite piles under vertical loads", U.S. Department of Transportation, Federal Highway Administration, Publication No. FHWAHRT-04-107.
  31. Kaliakin, V.N. and Li, J. (1995), "Insight into deficiencies associated with commonly used zero-thickness interface elements", Comput. Geotech., 17(2), 225-252. https://doi.org/10.1016/0266-352X(95)93870-O
  32. Katona, M.G. (1983), "A simple contact friction interface element with applications to buried culverts", Int. J. Numer. Anal. Meth. Geomech., 7(3), 371-384. https://doi.org/10.1002/nag.1610070308
  33. Kondner, R.L. (1963), "Hyperbolic stress-strain response: Cohesive soils", J. Soil Mech. Found. Div., ASCE, 89(SM1), 115-143.
  34. Kondner, R.L. and Zelasko, J.S. (1963), "A hyperbolic stress-strain formulation for sands", Proceedings of the 2nd Pan-American Conference on Soil Mechanics and Foundations Engineering, Sao Paulo, Brazil, July, Volume I, pp. 289-324.
  35. Kulhaway, F.H. and Peterson, M.S. (1979), "Behavior of sand and concrete interfaces", Proceedings of the 6th Pan American Conference on Soil Mechanics and Foundation Engineering, Sao Paulo, Brazil, July, Volume 2, pp. 225-230.
  36. Kurian, N.P. and Shah, S.J. (2009), "Studies on the behaviour of screw piles by the finite element method", Can. Geotech. J., 46(6), 627-638. https://doi.org/10.1139/T09-008
  37. Martin, C., Jefferis, S. and Lam, C. (2014), "Effects of polymer and bentonite support fluids on concrete-sand interface shear strength", Geotechnique, 64(1), 28-39. https://doi.org/10.1680/geot.13.P.012
  38. Liu, H.B., Song, E.X. and Ling, I.L. (2006), "Constitutive modeling of soil-structure interface through the concept of critical state soil mechanics", Mech. Res. Commun., 33(4), 515-531. https://doi.org/10.1016/j.mechrescom.2006.01.002
  39. Livneh, B. and El Naggara, M.H. (2008), "Axial testing and numerical modeling of square shaft helical piles under compressive and tensile loading", Can. Geotech. J., 45(8), 1142-1155. https://doi.org/10.1139/T08-044
  40. Lutenneger, A.J. (2011), "Behavior of multi-helix screw anchors in sand", Proceedings of the 14th Pan-American Conference on Soil Mechanics and Geotechnical Engineering, Toronto, ON, Canada, October.
  41. Mittal, S. and Mukherjee, S. (2015), "Behaviour of group of helical screw anchors under compressive loads", Geotech. Geol. Eng., 33(3), 575-592. https://doi.org/10.1007/s10706-015-9841-4
  42. Mortara, G., Boulon, M. and Ghionna, V.N. (2002), "A 2-D constitutive model for cyclic interface behaviour", Int. J. Numer. Anal. Meth. Geomech., 26(11), 1071-1096. https://doi.org/10.1002/nag.236
  43. Paikowsky, S.G., Player, C.M. and Connors, P.J. (1995), "A dual interface apparatus for testing unrestricted friction of soil along solid surfaces", Geotech. Test. J., 18(2), 168-193. https://doi.org/10.1520/GTJ10320J
  44. Papadopoulou, K., Saroglou, H. and Papadopoulos, V. (2014), "Finite element analyses and experimental investigation of helical micropiles", Geotech. Geol. Eng., 32(4), 949-963. https://doi.org/10.1007/s10706-014-9771-6
  45. Potyondy, J.G. (1961), "Skin friction between various soils and construction material", Geotechnique, 11(4), 339-353. https://doi.org/10.1680/geot.1961.11.4.339
  46. Qian, J.G., Chen, H.W. and Huang, M.S. (2013), "Numerical modeling pile-soil interface of grouting screw uplift pile", International Symposium on Advances in Foundation Engineering, Singapore, December. DOI: 10.3850/978-981-07-4623-0_129
  47. Sakr, M. (2009), "Performance of helical piles in oil sand", Can. Geotech. J., 46(9), 1046-1061. DOI: 10.1139/T09-044
  48. Tsuha, C.H.C., Aoki, N., Rault, G., Thorel, L. and Garnier, J. (2012), "Evaluation of the efficiencies of helical anchor plates in sand by centrifuge model tests", Can. Geotech. J., 49(9), 1102-1114. https://doi.org/10.1139/t2012-064
  49. Uesugi, M. and Kishida, H. (1986a), "Influential factors of between steel and dry sands", Soils Found., 26(2), 33-46. https://doi.org/10.3208/sandf1972.26.2_33
  50. Uesugi, M. and Kishida, H. (1986b), "Frictional resistance at yield between dry sand and mild steel", Soils Founda., 26(4), 139-149. https://doi.org/10.3208/sandf1972.26.4_139
  51. Villard, P. (1996), "Modelling of interface problems by the finite element method with considerable displacements", Comput. Geotech., 19(1), 23-45. https://doi.org/10.1016/0266-352X(95)00035-9
  52. Wang, J. and Jiang, M. (2011), "Unified soil behavior of interface shear test and direct shear test under the influence of lower moving boundaries", Granular Matter, 13(5), 631-641. https://doi.org/10.1007/s10035-011-0275-2
  53. Wang, J., Dove, J.E. and Gutierrez, M.S. (2007), "Determining particulate-solid interphase strength using shear-induced anisotropy", Granular Matter, 9(3-4), 231-240. https://doi.org/10.1007/s10035-006-0031-1
  54. Yoshimi, Y. and Kishida, T. (1981), "A ring torsion apparatus for evaluation friction between soil and metal surface ", Geotech. Test. J., 4(4), 145-152. https://doi.org/10.1520/GTJ10783J
  55. Zeghal, M. and Edil, T. (2002), "Soil structure interaction analysis: modeling the interface", Can. Geotech. J., 39(3), 620-628. https://doi.org/10.1139/t02-016
  56. Zienkiewicz, O.C., Best, B., Dulllage, C. and Stagg, K.G. (1970), "Analysis of nonlinear problems with particular reference to jointed rock systems", Proceedings of the 2nd International Congress on Society of Rock Mechanics, Beograd, Serbia, September, Volume 3, pp. 501-509.
  57. Zhou, W.H., Yin, J.H. and Hong, C.Y. (2011), "Finite element modelling of pullout testing on a soil nail in a pullout box under different overburden and grouting pressures", Can. Geotech. J., 48(4), 557-567. https://doi.org/10.1139/t10-086
  58. Zhou, J., Chen, J.F., Xue, J.F. and Wang, J.Q. (2012), "Micro-mechanism of the interaction between sand and geogrid transverse ribs", Geosynth. Int., 19(6), 426-437. https://doi.org/10.1680/gein.12.00028

피인용 문헌

  1. Sand–concrete interface response: The role of surface texture and confinement conditions vol.59, pp.6, 2017, https://doi.org/10.1016/j.sandf.2019.05.013
  2. FRACTAL CHARACTERIZATION AND MECHANICAL BEHAVIOR OF PILE-SOIL INTERFACE SUBJECTED TO SULFURIC ACID vol.29, pp.2, 2017, https://doi.org/10.1142/s0218348x21400107