DOI QR코드

DOI QR Code

Influence of different fatigue loads and coating thicknesses on service performance of RC beam specimens with epoxy-coated reinforcement

  • Wang, Xiao-Hui (School of Energy, Geoscience, Infrastructure and Society, Heriot-Watt University) ;
  • Gao, Yang (Shanghai Municipal Engineering Design Institute (Group) Co., LTD.) ;
  • Gao, Run-Dong (Shanghai Key Laboratory of Engineering Structure Safety) ;
  • Wang, Jing (Dept. of Civil Engineering, Shanghai Jiao Tong Univ.) ;
  • Liu, Xi-La (Dept. of Civil Engineering, Shanghai Jiao Tong Univ.)
  • Received : 2014.10.16
  • Accepted : 2016.12.22
  • Published : 2017.03.25

Abstract

Epoxy-coated reinforcing bars are widely used to protect the corrosion of the reinforcing bars in the RC elements under their in-service environments and external loads. In most field surveys, it was reported that the corrosion resistance of the epoxy-coated reinforcing bars is typically better than the uncoated bars. However, from the experimental tests conducted in the labs, it was reported that, under the same loads, the RC elements with epoxy-coated reinforcing bars had wider cracks than the elements reinforced with the ordinary bars. Although this conclusion may be true considering the bond reduction of the reinforcing bar due to the epoxy coating, the maximum service loads used in the experimental research may be a main reason. To answer these two phenomena, service performance of 15 RC beam specimens with uncoated and epoxy-coated reinforcements under different fatigue loads was experimentally studied. Influences of different coating thicknesses of the reinforcing bars, the fatigue load range and load upper limit as well as fatigue load cycles on the mechanical performance of RC test specimens are discussed. It is concluded that, for the test specimens subjected to the comparatively lower load range and load upper limit, adverse effect on the service performance of test specimens with thicker epoxy-coated reinforcing bars is negligible. With the increments of the coating thickness and the in-service loading level, i.e., fatigue load range, load upper limit and fatigue cycles, the adverse factor resulting from the thicker coating becomes noticeable.

Keywords

Acknowledgement

Supported by : National Natural Science Foundation of China

References

  1. Abrishami, H.H., Cook, W.D. and Mitchell, D. (1995), "Influence of epoxy-coated reinforcement on response of normal and high-strength concrete beams", ACI Struct. J., 92(2), 157-166.
  2. Cairns, J. (1994), "Performance of epoxy-coated reinforcement at the serviceability limit state", Proceedings of the Institution of Civil Engineering Structures and Buildings, 104(1), 61-73. https://doi.org/10.1680/istbu.1994.25680
  3. Cairns, J. and Abdullah, R. (1994), "Fundamental tests on the effect of an epoxy coating on bond strength", ACI Mater. J., 91(4), 331-338.
  4. Cairns, J. and Abdullah, R.B. (1995), "Influence of rib geometry on strength of epoxy-coated reinforcement", ACI Struct. J., 92(1), 23-27.
  5. Castro, P.F. (1996), "Influence of coatings on bar-concrete bond", J. Mater. Civ. Eng., 8(4), 212-214. https://doi.org/10.1061/(ASCE)0899-1561(1996)8:4(212)
  6. Cleary, D.B. and Ramirez, J.A. (1991), "Bond strength of epoxy-coated reinforcement", ACI Mater. J., 88(2), 146-149.
  7. Cleary, D.B. and Ramirez, J.A. (1993), "Epoxy-coated reinforcement under repeated loading", ACI Struct. J., 90(4), 451-458.
  8. Cusson, D., Qian, S., Chagnon, N. and Baldock, B. (2008), "Corrosion-inhibiting systems for durable concrete bridges. I: five-year field performance evaluation", J. Mater. Civ. Eng., 20(1), 20-28. https://doi.org/10.1061/(ASCE)0899-1561(2008)20:1(20)
  9. De Anda, L., Courtier, C. and Moehle, J.P. (2006), "Bond strength of prefabricated epoxy-coated reinforcement", ACI Struct. J., 103(2), 226-234.
  10. Erdogdu, S., Bremner, T.W. and Kondratova, I.L. (2001), "Accelerated testing of plain and epoxy-coated reinforcement in simulated seawater and chloride solutions", Cement Concrete Res., 31(6), 861-867. https://doi.org/10.1016/S0008-8846(01)00487-2
  11. Fanous, F. and Wu, H. (2005), "Performance of coated reinforcing bars in cracked bridge decks", J. Bridge Eng., 10(3), 255-261. https://doi.org/10.1061/(ASCE)1084-0702(2005)10:3(255)
  12. Fei, J. and Darwin, D. (1999), "Fatigue of high relative rib area reinforcing bars", Ph.D. Diessertation, University of Kansas Center for Research, Kansas, U.S.A.
  13. Fib Task Group Bond Models (2000), State-of-Art Report on Bond of Reinforcement in Concrete, 232-235.
  14. GB50010-2010 (2010), Code for Design of Concrete Structures, National Standards of People's Republic of China, Beijing, China.
  15. Hamad, B.S. (1995), "Comparative bond strength of coated and uncoated bars with different rib geometries", ACI Mater. J., 92(6), 579-590.
  16. Hamad, B.S., Jirsa, J.O. and D'Abreu de Paulo, N.I. (1993), "Anchorage strength of epoxy-coated hooked bars", ACI Struct. J., 90(2), 210-217.
  17. Hasan, H.O., Cleary, D.B. and Ramirez, J.A. (1996), "Performance of concrete bridge decks and slabs reinforced with epoxy-coated steel under repeated loading", ACI Struct. J., 93(4), 397-403.
  18. Idun, E.K. and Darwin, D. (1999), "Bond of epoxy-coated reinforcement: Coefficient of friction and rib face angle", ACI Struct. J., 96(4), 609-615.
  19. JG3042-1997 (1997), Epoxy Resin Coated Steel Bars, Construction Industry Standard of the People's Republic of China, Beijing, China.
  20. Johnston, D.W. and Zia, P. (1984), "Bond fatigue of epoxy coated reinforcing bars", Mater. Struct., 17(1), 30-34.
  21. Kayyali, O.A. and Yeomans, S.R. (1995), "Bond and slip of coated reinforcement in concrete", Construct. Build. Mater., 9(4), 219-226. https://doi.org/10.1016/0950-0618(95)00024-A
  22. Lau, K., Sagues, A.A. and Powers, R.G. (2010), "Corrosion of epoxy-coated rebar in marine bridges-part 2: Corrosion in cracked concrete", Corros., 66(6), 0650021-06500216.
  23. Lawler, J.S., Krauss, P.D., Kurth, J. and McDonald, D. (2011), "Condition survey of older west Virginia bridge decks constructed with epoxy-coated reinforcing bars", Transp. Res. Rec.: J. Transp. Res. Board., 2220, 57-65. https://doi.org/10.3141/2220-07
  24. Manning, D.G. (1996), "Corrosion performance of epoxy-coated reinforcing steel: North American experience", Constr. Build. Mater., 10(5), 349-365. https://doi.org/10.1016/0950-0618(95)00028-3
  25. Montes, P., Bremner, T.W. and Kondratova, I. (2004), "Eighteen-year performance of epoxy-coated rebar in a tunnel structure subjected to a very aggressive chloride-contaminated environment", Corros., 60(10), 974-981. https://doi.org/10.5006/1.3287832
  26. Oh, B.H. and Kim, S.H. (2007), "Realistic models for local bond stress-slip of reinforced concrete under repeated loading", J. Struct. Eng., 133(2), 216-224. https://doi.org/10.1061/(ASCE)0733-9445(2007)133:2(216)
  27. Rehm, G. and Eligehausen, R. (1979), "Bond of ribbed bars under high cycle repeated loads", ACI J., 76(2), 297-309.
  28. Sagues, A.A., Lau, K., Powers, R.G. and Kessler, R.J. (2010), "Corrosion of epoxy-coated rebar in marine bridges-part 1: A 30-year perspective", Corros., 66(6), 0650011-06500113.
  29. Selvaraj, R., Selvaraj, M. and Iyer, S.V.K. (2009), "Studies on the evaluation of the performance of organic coatings used for the prevention of corrosion of steel rebars in concrete structures", Prog. Org. Coat., 64(4), 454-459. https://doi.org/10.1016/j.porgcoat.2008.08.005
  30. Smith, J.L. and Virmani, Y.P. (1996), "Performance of epoxy-coated rebars in bridge decks", Public Roads, 60(2), 6-12.
  31. Sohanghpurwala, A.A. (2005), "Condition and performance of epoxy-coated rebars in bridge decks of the state of Pennsylvania and New York", Proceedings of the Structures Congress and the Forensic Engineering Symposium, American Society of Civil Engineers, New York, U.S.A., April.
  32. Treece, R.A. and Jirsa, J.O. (1989), "Bond strength of epoxy-coated reinforcing bars", ACI Mater. J., 86(2), 167-174.
  33. Venkatesan, P., Palaniswamy, N. and Rajagopal, K. (2006), "Corrosion performance of coated reinforcing bars embedded in concrete and exposed to natural marine environment", Prog. Org. Coat., 56(1), 8-12. https://doi.org/10.1016/j.porgcoat.2006.01.011
  34. Walraven, J.C. (2008), Eurocode 2, Design of Concrete Structures, EN1992-1-1, Brussels, Belgium.
  35. Weyers, R.E., Pyc, W., Zemajtis, J., Liu, Y., Mokarem, D. and Sprinkel, M.M. (1997), "Field investigation of corrosion-protection performance of bridge decks constructed with epoxy-coated reinforcing steel in Virginia", Transp. Res. Rec.: J. Transp. Res. Board, 1597, 82-90. https://doi.org/10.3141/1597-11
  36. Yeih, W., Chang, J.J. and Tsai, C.L. (2004), "Enhancement of the bond strength of epoxy coated steel by the addition of fly ash", Cement Concrete Compos., 26(4), 315-321. https://doi.org/10.1016/S0958-9465(02)00142-7

Cited by

  1. Probabilistic analysis of chloride penetration in reinforced concrete subjected to pre-exposure static and fatigue loading and wetting-drying cycles vol.84, 2018, https://doi.org/10.1016/j.engfailanal.2017.11.008
  2. Bayesian Assessment of the Effects of Cyclic Loads on the Chloride Ingress Process into Reinforced Concrete vol.10, pp.6, 2017, https://doi.org/10.3390/app10062040