DOI QR코드

DOI QR Code

Interfacial properties of composite shotcrete containing sprayed waterproofing membrane

  • Park, Byungkwan (School of Smarty City and Construction Engineering, University of Science and Technology (UST)) ;
  • Lee, Chulho (School of Smarty City and Construction Engineering, University of Science and Technology (UST)) ;
  • Choi, Soon-Wook (Department of Infrastructure Safety Research, Korea Institute of Civil Engineering and Building Technology) ;
  • Kang, Tae-Ho (Department of Infrastructure Safety Research, Korea Institute of Civil Engineering and Building Technology) ;
  • Kim, Jintae (Silkroad T&D Co., Ltd.) ;
  • Choi, Myung-Sik (Silkroad T&D Co., Ltd.) ;
  • Jeon, Seokwon (Department of Energy Resources Engineering, Seoul National University) ;
  • Chang, Soo-Ho (School of Smarty City and Construction Engineering, University of Science and Technology (UST))
  • Received : 2018.02.19
  • Accepted : 2018.07.30
  • Published : 2018.11.20

Abstract

This study evaluates the interfacial properties of composite specimens consisting of shotcrete and sprayed waterproofing membrane. Two different membrane prototypes were first produced and tested for their waterproofing ability. Then composite specimens were prepared and their interfacial properties assessed in direct shear and uniaxial compression tests. The direct shear test showed the peak shear strength and shear stiffness of the composites' interface decreased as the membrane layer became thicker. The shear stiffness, a key input parameter for numerical analysis, was estimated to be 0.32-1.74 GPa/m. Shear stress transfer at the interface between the shotcrete and membrane clearly emerged when measuring peak shear strengths (1-3 MPa) under given normal stress conditions of 0.3-1.5 MPa. The failure mechanism was predominantly shear failure at the interface in most composite specimens, and shear failure in the membranes. The uniaxial compression test yielded normal stiffness values for the composite specimens of 5-24 GPa/m. The composite specimens appeared to fail by the compressive force forming transverse tension cracks, mainly around the shotcrete surface perpendicular to the membrane layer. Even though the composite specimens had strength and stiffness values sufficient for shear stress transfer at the interfaces of the two shotcrete layers and the membrane, the sprayed waterproofing membrane should be as thin as possible whilst ensuring waterproofing so as to obtain higher strength and stiffness at the interface.

Keywords

Acknowledgement

Supported by : Korea Agency for Infrastructure Technology Advancement

References

  1. ASTM (2010), Standard Test Method for Tensile Properties of Plastics, ASTM D638-10.
  2. ASTM (2015), Standard Test Method for Rubber Property Durometer Hardness, ASTM D2240-15.
  3. BS EN 1542:1999 (1999), Products and Systems for the Protection and Repair of Concrete Structures, Test Methods, Measurement of Bound Strength by Pull-Iff.
  4. BS EN 1766: 2000 (2000), Products and Systems for the Protection and Repair of Concrete Structures, Test Methods, Reference Concretes for Testing.
  5. Chang, S.H., Lee, C., Kang, T.H., Ha, T. and Choi, S.W. (2017), "Effect of hardfacing on wear reduction of pick cutters under mixed rock conditions", Geomech. Eng., 13(1), 141-159. https://doi.org/10.12989/GAE.2017.13.1.141
  6. EFNARC (2008), Specification and Guidelines on Thin Spray-on Liners for Mining and Tunnelling, ENC 250TSL v7.2 25-07-08.
  7. EN 12390-8 (2009), Testing Hardened Concrete-Part 8: Depth of Penetration of Water under Pressure.
  8. EN 14891 (2006), Liquid Applied Water Impermeable Products for Use beneath Ceramic Tiling Bonded with Adhesives-Requirements, Test Methods, Evaluation of Conformity, Classification and Designation.
  9. Holter, K.G. (2014), "Loads on sprayed waterproof tunnel linings in jointed hard rock: A study based on Norwegian cases", Rock Mech. Rock Eng., 47(3), 1003-1020. https://doi.org/10.1007/s00603-013-0498-0
  10. Holter, K.G. (2016), "Performance of EVA-based membranes for SCL in hard rock", Rock Mech. Rock Eng., 49(4), 1329-1358.
  11. Holter, K.G. and Foord, R. (2015), "Testing of properties and constructability considerations of EVA-based sprayed membranes for waterproofing of tunnels", Proceedings of the ITA WTC 2015 Congress and 41st General Assembly, Dubrovnik, Croatia.
  12. Holter, K.G. and Gerving, S. (2016), "Moisture transport through sprayed concrete tunnel linings", Rock Mech. Rock Eng., 49(1), 243-272. https://doi.org/10.1007/s00603-015-0730-1
  13. Holter, K.G., Nilsen, B., Langas, C. and Tandberg, M.K. (2014), "Testing of sprayed waterproofing membranes for single shell sprayed concrete tunnel linings in hard rock", Proceedings of the World Tunnel Congress 2014 and 40th ITA-AITES General Assembly, Iguassu Falls, Brazil, May.
  14. ITAtech (2013), Design Guidance for Spray Applied Waterproofing Membranes, ITAtech Report No. 2, ISBN 978-2-9700858-1-2.
  15. Johnson, R.P., Swallow, F.E. and Psomas, S. (2016), "Structural properties and durability of a sprayed waterproofing membrane for tunnels", Tunn. Undergr. Sp. Technol., 60, 41-48.
  16. Kim, K.Y., Yun, T.S., Choo, J., Kang, D.H. and Shin, H.S. (2012), "Determination of air-void parameters of hardened cement-based materials using X-ray computed tomography", Construct. Build. Mater., 37, 93-101. https://doi.org/10.1016/j.conbuildmat.2012.07.012
  17. Nakashima, M., Hammer, A.L., Thewes, M., Elshafie, M. and Soga, K. (2015), "Mechanical behavior of a sprayed concrete lining isolated by a sprayed waterproofing membrane", Tunn. Undergr. Sp. Technol., 47, 143-152. https://doi.org/10.1016/j.tust.2015.01.004
  18. Stubberfield, K. (2016), Masterseal 345(R) Application Course - Lecture Material, Tunnelling & Underground Construction Academy (TUCA), London, U.K., April 13, 2016.
  19. Su, J. and Bloodworth, A. (2016), "Interface parameters of composite sprayed concrete linings in soft ground with spray-applied waterproofing", Tunn. Undergr. Sp. Technol., 59, 170-182. https://doi.org/10.1016/j.tust.2016.07.006
  20. Thomas, A. (2009) Sprayed Concrete Lined Tunnels, Taylor & Francis, London, U.K.
  21. Verani, C.A. and Aldrian, W. (2010), Composite Linings: Ground Support and Waterproofing through the Use of a Fully Bonded Membrane, in Shotcrete: Element of a System, Taylor & Francis, London, U.K., 269-282.
  22. Vogel, F., Sovjak, R. and Peskova, S. (2017), "Static response of double shell concrete lining with a spray-applied waterproofing membrane", Tunn. Undergr. Sp. Technol., 68, 106-112. https://doi.org/10.1016/j.tust.2017.05.022

Cited by

  1. 차수용 박층 멤브레인의 직접전단실험에 관한 수치해석 연구 vol.17, pp.4, 2018, https://doi.org/10.12814/jkgss.2018.17.4.189