DOI QR코드

DOI QR Code

Estimating UCS of cement-grouted sand using characteristics of sand and UCS of pure grout

  • Lee, Changho (Department of Marine and Civil Engineering, Chonnam National University) ;
  • Nam, Hongyeop (School of Civil, Environmental and Architectural Engineering, Korea University) ;
  • Lee, Woojin (School of Civil, Environmental and Architectural Engineering, Korea University) ;
  • Choo, Hyunwook (Department of Civil Engineering, Kyung Hee University) ;
  • Ku, Taeseo (Department of Civil and Environmental Engineering, National University of Singapore)
  • 투고 : 2019.07.12
  • 심사 : 2019.11.08
  • 발행 : 2019.11.20

초록

For quality control and the economical design of grouted sand, the prior establishment of the unconfined compressive strength (UCS) estimating formula is very important. This study aims to develop an empirical UCS estimating formula for grouted sand based on the physical properties of sands and the UCS of cured pure grout. Four sands with varying particle sizes were grouted with both microfine cement and Ordinary Portland cement. Grouted specimens were prepared at three different relative densities and at three different water-to-cement ratios, and unconfined compression tests were performed. The results demonstrate that UCS of grouted sand can be expressed as the power function of the UCS of cured pure grout: $UCS_{grouted\;sand}/1MPa=A_{soil}{\cdot}(UCS_{pure}/1MPa)^N$. Because the exponent N strongly depends on the combination of pore area and pore size, N is expressed as the function of porosity (n) and specific surface ($S_a$). Additionally, because $S_a$ determines the area of the sand particle that cement particles can adsorb and n determines the number of cementation bondings between sand particles, $A_{soil}$ is also expressed as the function of n and $S_a$. Finally, the direct relationship between $A_{soil}$ and N is also investigated.

키워드

과제정보

연구 과제 주관 기관 : National Research Foundation of Korea (NRF)

참고문헌

  1. Abramson, L.W., Lee, T.S., Sharma, S. and Boyce, G.M. (2002), Slope Stability and Stabilization Methods, John Wiley & Sons., Hoboken, New Jersey, U.S.A.
  2. Akbulut, S. and Saglamer, A. (2002), "Estimating the groutability of granular soils: A new approach", Tunn. Undergr. Sp. Technol., 17(4), 371-380. https://doi.org/10.1016/S0886-7798(02)00040-8.
  3. ASTM-C940-98a (2003), "Standard test method for expansion and bleeding of freshly mixed grouts for preplaced-aggregate concrete in the laboratory", Annual Book of ASTM Standards, ASTM, West Conshohocken, Pennsylvania, U.S.A.
  4. Avci, E. and Mollamahmutoglu, M. (2016), "UCS roperties of superfine cement-grouted sand", J. Mater. Civ. Eng., 28(12), 06016015. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001659.
  5. Azadi, M.R., Taghichian, A. and Taheri, A. (2017), "Optimization of cement-based grouts using chemical additives", J. Rock Mech. Geotech. Eng., 9(4), 623-637., https://doi.org/10.1016/j.jrmge.2016.11.013.
  6. Brachman, R.W.I., Martin, C.D. and Gilliss, S.A. (2004), "Grout field trials in outwash sands", Can. Geotech. J., 41(1), 1-11. https://doi.org/10.1139/t03-069.
  7. Bruce, D.A., Littlejohn, G.S. and Naudts, A. (1997), "Grouting materials for ground treatment: A practitioner's guide", Proceedings of the Sessions Sponsored by the Grouting Committee of the Geo-Institute of the American Society of Civil Engineers in Conjuction with the Geo-Logan'97 Conference, Logan, Utah, U.S.A., July.
  8. Celik, F. (2019), "The observation of permeation grouting method as soil improvement technique with different grout flow models", Geomech. Eng., 17(4), 367-374. https://doi.org/10.12989/gae.2019.17.4.367.
  9. Chaney, R. and Mulilis, J. (1978), "Suggested method for soil specimen remolding by wet-raining", Geotech. Test. J., 1(2), 107-108., https://doi.org/10.1520/GTJ10378J.
  10. Chang, M.H., Mao, T.W. and Huang, R.C. (2016), "A study on the improvements of geotechnical properties of in-situ soils by grouting", Geomech. Eng., 10(4), 527-546. http://dx.doi.org/10.12989/gae.2016.10.4.527.
  11. Choo, H., Lee, W. and Lee, C. (2018), "Overconsolidation and Cementation in Sands: Impacts on Geotechnical Properties and Evaluation Using Dilatometer Tests", Geotech. Test. J., 41(5), 915-929., https://doi.org/10.1520/GTJ20170368.
  12. Choo, H., Lee, W., Lee, C. and Burns, S.E. (2018), "Estimating porosity and particle size for hydraulic conductivity of binary mixed soils containing two different-sized silica particles", J. Geotech. Geoenviron. Eng., 144(1), 04017104. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001802.
  13. Choo, H., Nam, H. and Lee, W. (2017), "A practical method for estimating maximum shear modulus of cemented sands using unconfined compressive strength", J. Appl. Geophys., 147, 102-108. https://doi.org/10.1016/j.jappgeo.2017.10.012.
  14. Clough, G.W., Sitar, N., Bachus, R.C. and Rad, N.S. (1981), "Cemented sands under static loading", J. Geotech. Eng. Div., 107(6), 799-817. https://doi.org/10.1061/AJGEB6.0001152
  15. Consoli, N.C., Foppa, D., Festugato, L. and Heineck, K.S. (2007), "Key parameters for strength control of artificially cemented soils", J. Geotech. Geoenviron. Eng., 133(2), 197-205. https://doi.org/10.1061/(ASCE)1090-0241(2007)133:2(197).
  16. Dano, C., Hicher, P.Y. and Tailliez, S. (2004), "Engineering properties of grouted sands", J. Geotech. Geoenviron. Eng., 130(3), 328-338. https://doi.org/10.1061/(ASCE)1090-0241(2004)130:3(328).
  17. De Paoli, B., Bosco, B., Granata, R. and Bruce, D. (1992), "Fundamental observations on cement based grouts (1):traditional materials", Proceedings of the ASCE Specialty Conference on Grouting, Soil Improvement and Geosynthetics, New Orleans, Louisiana, U.S.A., February.
  18. Eklund, D. and Stille, H. (2008), "Penetrability due to filtration tendency of cement-based grouts", Tunn. Undergr. Sp. Technol., 23(4), 389-398. https://doi.org/10.1016/j.tust.2007.06.011.
  19. Fredlund, M.D., Fredlund, D. and Wilson, G.W. (2000), "An equation to represent grain-size distribution", Can. Geotech. J., 37(4), 817-827. https://doi.org/10.1139/t00-015.
  20. Gallagher, P.M. and Mitchell, J.K. (2002), "Influence of colloidal silica grout on liquefaction potential and cyclic undrained behavior of loose sand", Soil Dyn. Earthq. Eng., 22(9-12), 1017-1026. https://doi.org/10.1016/S0267-7261(02)00126-4
  21. Gallagher, P.M., Pamuk, A. and Abdoun, T. (2007), "Stabilization of liquefiable soils using colloidal silica grout", J. Mater. Civ. Eng., 19(1), 33-40. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:1(33).
  22. Gopinathan, S. and Anand, K.B. (2018), "Properties of cement grout modified with ultra-fine slag", Front. Struct. Civ. Eng., 12(1), 58-66., https://doi.org/10.1007/s11709-017-0383-0.
  23. Hoek, E. (2001), "Big tunnels in bad rock", J. Geotech. Geoenviron. Eng., 127(9), 726-740. https://doi.org/10.1061/(ASCE)1090-0241(2001)127:9(726).
  24. Hsiao, D.H., Phan, V.T.A. and Huang, C.C. (2016), "An experimental investigation on dynamic properties of various grouted sands", Geomech. Eng., 10(1), 77-94., http://dx.doi.org/10.12989/gae.2016.10.1.077.
  25. Huang, J. and Airey, D. (1998), "Properties of artificially cemented carbonate sand", J. Geotech. Geoenviron. Eng., 124(6), 492-499. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:6(492).
  26. Ismail, M.A., Joer, H.A., Randolph, M.F. and Meritt, A. (2002), "Cementation of porous materials using calcite", Geotechnique, 52(5), 313-324. https://doi.org/10.1680/geot.2002.52.5.313.
  27. Kaga, M. and Yonekura, R. (1991), "Estimation of strength of silicategrouted sand", Soils Found., 31(3), 43-59. https://doi.org/10.3208/sandf1972.31.3_43.
  28. Li, S.C., Sha, F., Liu, R.T., Zhang, Q.S. and Li, Z.F. (2017), "Investigation on fundamental properties of microfine cement and cement-slag grouts", Construct. Build. Mater., 153, 965-974. https://doi.org/10.1016/j.conbuildmat.2017.05.188.
  29. Mahabadi, N. and Jang, J. (2017), "The impact of fluid flow on force chains in granular medium", Appl. Phys. Lett., 110(4), 041907. https://doi.org/10.1063/1.4975065.
  30. Markou, I. and Droudakis, A. (2013), "Factors affecting engineering properties of microfine cement grouted sands", Geotech. Geol. Eng., 31(4), 1041-1058. https://doi.org/10.1007/s10706-013-9631-9.
  31. Mirza, J., Saleh, K., Langevin, M.A., Mirza, S., Bhutta, M.A.R. and Tahir, M.M. (2013), "Properties of microfine cement grouts at 4 degrees C, 10 degrees C and 20 degrees C", Construct. Build. Mater., 47, 1145-1153. https://doi.org/10.1016/j.conbuildmat.2013.05.026.
  32. Mollamahmutoglu, M. and Avci, E. (2015), "Effectiveness of microfine portland cement grouting on the strength and permeability of medium to fine sands", Periodica Polytechnica Civ. Eng., 59(3), 319-326., https://doi.org/10.3311/PPci.7674.
  33. Nonveiller, E. (2013), Grouting Theory and Practice, Elsevier, Amsterdam, The Netherlands
  34. Ozgurel, H.G. and Vipulanandan, C. (2005), "Effect of grain size and distribution on permeability and mechanical behavior of acrylamide grouted sand", J. Geotech. Geoenviron. Eng., 131(12), 1457-1465. https://doi.org/10.1061/(ASCE)1090-0241(2005)131:12(1457).
  35. Pantazopoulos, I. and Atmatzidis, D. (2012), "Dynamic properties of microfine cement grouted sands", Soil Dyn. Earthq. Eng., 42, 17-31. https://doi.org/10.1016/j.soildyn.2012.05.017.
  36. Pantazopoulos, I., Markou, I., Christodoulou, D., Droudakis, A., Atmatzidis, D., Antiohos, S. and Chaniotakis, E. (2012), "Development of microfine cement grouts by pulverizing ordinary cements", Cement Concrete Compos., 34(5), 593-603. https://doi.org/10.1016/j.cemconcomp.2012.01.009.
  37. Pantazopoulos, I.A. and Atmatzidis, D.K. (2012), "Dynamic properties of microfine cement grouted sands", Soil Dyn. Earthq. Eng., 42, 17-31. https://doi.org/10.1016/j.soildyn.2012.05.017.
  38. Santamarina, J.C., Klein, K.A. and Fam, M.A. (2001), Soils and Waves: Particulate Materials Behavior, Characterization and Process Monitoring, J. Wiley & Sons, Chichester, England, U.K.
  39. Schwarz, L.G. and Chirumalla, M. (2007), "Effect of injection pressure on permeability and strength of microfine cement grouted sand", Proceedings of the GeoDenver 2007, New Peaks in Geotechnics, Denver, Colorado, U.S.A., February.
  40. Schwarz, L.G. and Krizek, R.J. (1994), "Effect of preparation technique on permeability and strength of cement-grouted sand", Geotech. Test. J., 17(4), 434-443. https://doi.org/10.1520/GTJ10304J.
  41. Sunitsakul, J., Sawatparnich, A. and Sawangsuriya, A. (2012), "Prediction of unconfined compressive strength of soil-cement at 7 days", Geotech. Geol. Eng., 30(1), 263-268. https://doi.org/10.1007/s10706-011-9460-7.
  42. Tinoco, J., Correia, A.G. and Cortez, P. (2011), "Application of data mining techniques in the estimation of the uniaxial compressive strength of jet grouting columns over time", Construct. Build. Mater., 25(3), 1257-1262., https://doi.org/10.1016/j.conbuildmat.2010.09.027.
  43. Van der Stoel, A.E.C. (2001), "Grouting for pile foundation improvement", Ph.D. Thesis, TU Delft, Delft University of Technology., Delft, The Netherlands
  44. Yang, L. and Salvati, L. (2010), "Small strain properties of sands with different cement types", Proceedings of the 5th International Conference on Recent Advances in Geotechnical Earthquake Engineering and Soil Dynamics and Symposium in Honor of Professor I.M. Idriss, San Diego, California, U.S.A., May.
  45. Yoon, J. and El Mohtar, C.S. (2014), "Groutability of granular soils using bentonite grout based on filtration model", Transport Porous Media, 102(3), 365-385. https://doi.org/10.1007/s11242-014-0279-6.
  46. Zebovitz, S., Krizek, R. and Atmatzidis, D. (1989), "Injection of fine sands with very fine cement grout", J. Geotech. Eng., 115(12), 1717-1733. https://doi.org/10.1061/(ASCE)0733-9410(1989)115:12(1717).
  47. Zheng, X., Perreault, F. and Jang, J. (2018), "Fines adsorption on nanoparticle-coated surface", Acta Geotechnica, 13(1), 219-226. https://doi.org/10.1007/s11440-017-0528-2.

피인용 문헌

  1. Correlating failure strength with wave velocities for cemented sands from the particle-level analysis vol.152, 2019, https://doi.org/10.1016/j.soildyn.2021.107062