DOI QR코드

DOI QR Code

Three-dimensional stability assessment of slopes with spatially varying undrained shear strength

  • Shi, Yunwei (School of Naval Architecture, Ocean & Civil Engineering, Shanghai Jiao Tong University) ;
  • Luo, Xianqi (School of Naval Architecture, Ocean & Civil Engineering, Shanghai Jiao Tong University) ;
  • Wang, Pingfan (School of Naval Architecture, Ocean & Civil Engineering, Shanghai Jiao Tong University)
  • 투고 : 2022.03.12
  • 심사 : 2022.11.14
  • 발행 : 2022.11.25

초록

The variation of the undrained shear strength (cu) is an important consideration for assessing slope stability in engineering practice. Previous studies focused on the three-dimensional (3D) stability of slopes in normally consolidated clays generally assume the undrained shear strength increases linearly with depth but does not vary in the horizontal direction. To assess the 3D stability of slopes with spatially varying undrained shear strength, the kinematic approach of limit analysis was adopted to obtain the upper bound solution to the stability number based on a modified failure mechanism. Three types failure mechanism: the toe failure, face failure and below-toe failure were considered. A serious of charts was then presented to illustrate the effect of key parameters on the slope stability and failure geometry. It was found that the stability and failure geometry of slopes are significantly influenced by the gradient of cu in the depth direction. The influence of cu profile inclination on the slope stability was found to be pronounced when the increasing gradient of cu in the depth direction is large. Slopes with larger width-to-height ratio B/H are more sensitive to the variation of cu profile inclination.

키워드

과제정보

The research described in this paper was financially supported by the National Natural Science Foundation of China (Project No.: 51208301). The authors wish to express their gratitude for the above financial support.

참고문헌

  1. Azarafza, M., Bonab, M.H. and Akgun, H. (2021), "Numerical analysis and stability assessment of complex secondary toppling failures: A case study for the south pars special zone", Geomech. Eng., 27(5), 481-495. https://doi.org/10.12989/gae.2021.27.5.481.
  2. Azhari, A. and Ozbay, U. (2018), "Role of geometry and stiffness contrast on stability of open pit mines struck by earthquakes", Geotech. Geol. Eng., 36(2), 1249-1266. https://doi.org/10.1007/s10706-017-0390-x.
  3. Bhandari, T., Hamad, F., Moormann, C., Sharmai, K.G. and Westrich, B. (2016), "Numerical modelling of seismic slope failure using MPM", Comput. Geotech., 75, 126-134. https://doi.org/10.1016/j.compgeo.2016.01.017.
  4. Bi, J.F., Luo, X.Q., Zhang, H.T. and Shen, H. (2019), "Stability analysis of complex rock slopes reinforced with prestressed anchor cables and anti-shear cavities", Bull. Eng. Geol. Environ., 78(2), 2027-2039. https://doi.org/10.1007/s10064-017-1171-8.
  5. Bjerrum, L. (1967), "Engineering geology of Norwegian normally consolidated marine clays as related to settlements of buildings", Geotechnique, 17(2), 83-118. https://doi.org/10.1680/geot.1967.17.2.83.
  6. Bonilla-Sierra, V., Scholtes, L., Donze, F.V. and Elmouttie, M.K. (2015), "Rock slope stability analysis using photogrammetric data and DFN-DEM modelling", Acta Geotech., 10(4), 497-511. https://doi.org/10.1007/s11440-015-0374-z.
  7. Bui, H.H., Fukagawa, R., Sako, K. and Wells, J.C. (2011), "Slope stability analysis and discontinuous slope failure simulation by elasto-plastic smoothed particle hydrodynamics (SPH)", Geotechnique, 61(7), 565-574. https://doi.org/10.1680/geot.9.P.046.
  8. Chehade, H.A., Dias, D., Sadek, M., Jenck, O. and Chehade, F.H. (2022), "Seismic internal stability of saturated reinforced soil retaining walls using the upper bound theorem of limit analysis", Soil Dyn. Earthq. Eng., 155, 107180. https://doi.org/10.1016/j.soildyn.2022.107180.
  9. Chen, W.F. (1975), Limit Analysis and Soil Plasticity, Elsevier Scientific Publishing Company, New York, NY, USA.
  10. Chen, Z.Y. (1992), "Random trials used in determining global minimum factors of safety of slopes", Can. Geotech. J., 29(2), 225-233. https://doi. org/ 10. 1139/ t92- 026. https://doi.org/10.1139/t92-026
  11. Deng, D.P., Lu, K. and Li, L. (2019), "LE analysis on unsaturated slope stability with introduction of nonlinearity of soil strength", Geomech. Eng., 19(2), 179-191. https://doi.org/10.12989/gae.2019.19.2.179.
  12. Farshidfar, N., Keshavarz, A. and Mirhosseini, S.M. (2021), "Seismic stability of reinforced soil slopes using the modified pseudo-dynamic method", Earthq. Struct., 20(5), 473-486. https://doi.org/10.12989/eas.2021.20.5.473.
  13. Feng, Z.K. and Xu, W.J. (2021), "GPU material point method (MPM) and its application on slope stability analysis", Bull. Eng. Geol. Environ., 80(7), 5437-5449. https://doi.org/10.1007/s10064-021-02265-8.
  14. Gao, G., Meguid, M.A., Chouinard, L.E. and Xu, C. (2020), "Insights into the transport and fragmentation characteristics of earthquake-induced rock avalanche: Numerical study", Int. J. Geomech., 20(9), 04020157. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001800.
  15. Gao, G., Meguid, M.A., Chouinard, L.E. and Zhan, W.W. (2021), "Dynamic disintegration processes accompanying transport of an earthquake-induced landslide", Landslides., 18(3), 909-933. https://doi.org/10.1007/s10346-020-01508-1.
  16. Gao, Y.F., Wu, D., Zhang, F., Lei, G.H., Qin, H.Y. and Qiu, Y. (2016), "Limit analysis of 3D rock slope stability with non-linear failure criterion", Geomech. Eng., 10(1), 59-76. https://doi.org/10.12989/gae.2016.10.1.059.
  17. Gibson, R.E. and Morgenstern, N. (1962), "A note on the stability of cuttings in normally consolidated clays", Geotechnique, 12(3), 212-216. https://doi.org/10.1680/geot.1962.12.3.212.
  18. Griffiths, D.V. and Yu, X. (2015), "Another look at the stability of slopes with linearly increasing undrained strength", Geotechnique, 65(10), 824-830. https://doi.org/10.1680/jgeot.14.T.030.
  19. Hassanikhah, A. and Drumm, E.C. (2020), "Stability and evolution of planar and concave slopes under unsaturated and rainfall conditions", Int. J. Geomech., 20(7), 04020099. https://doi.org/10.1061/(ASCE)GM.1943-5622.0001662.
  20. He, Y., Hazarika, H., Yasufuku, N., Han, Z. and Li, Y.G. (2015), "Three-dimensional limit analysis of seismic displacement of slope reinforced with piles", Soil Dyn. Earthq. Eng., 77, 446-452. http://dx.doi.org/10.1016/j.soildyn.2015.06.015.
  21. Hossley, A. and Lenshchinsky, B. (2019), "Stability and failure geometry of slopes with spatially varying undrained shear strength", J. Geotech. Geoenviron. Eng., 145(5), 06019002. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002046.
  22. Hunter, J.H. and Schuster, R.L. (1968), "Stability of simple cuttings in normally consolidated clays", Geotechnique, 18(3), 372-378. https://doi.org/10.1680/geot.1968.18.3.372.
  23. Ke, L.J., Gao, Y.F., Zhao, Z.H., Zhou, Y.D. and Ji, J. (2021), "Undrained bearing capacity of strip footing near slopes considering the orientation of strength increase", Int. J. Geomech., 21(7), 06021016. https://doi.org/10.1061/(ASCE)GM.1943-5622.0002088.
  24. Koppula, S.D. (1984), "On stability of slopes in clays with linearly increasing strength", Can. Geotech. J., 21(3), 577-581. https://doi.org/10.1139/t84-059.
  25. Kumar, J., Chakraborty, M. and Sahoo, J.P. (2014), "Stability of unsupported vertical circular excavations", J. Geotech. Geoenviron. Eng., 140(7), 04014028. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001118.
  26. Li, A.J., Merifield, R.S. and Lyamin, A.V. (2009), "Limit analysis solutions for three dimensional undrained slopes", Comput. Geotech., 36(8), 1330-1351. https://doi.org/10.1016/j.compgeo.2009.06.002.
  27. Li, A.J., Merifield, R.S. and Lyamin, A.V. (2010), "Three-dimensional stability charts for slopes based on limit analysis methods", Can. Geotech. J., 47(12), 1316-1334. https://doi.org/10.1139/T10-030.
  28. Li, B., Zhang, F. and Wang, D. (2018), "Impact of crack on stability of slope with linearly increasing undrained strength", Math. Probl. Eng., 2018, 1096513. https://doi.org/10.1155/2018/1096513.
  29. Li, W., Li, J.B., Tang, G.P., Chen, J.Y. and Dai, C.L. (2021), "Upper-bound limit analysis for slope stability based on modified Mohr-Coulomb failure criterion with tensile cutoff", Int. J. Geomech., 21(10), 04021184. https://doi.org/10.1061/(ASCE)GM.1943-5622.0002154.
  30. Mesri, G. and Shahien, M. (2003), "Residual shear strength mobilized in first-time slope failures", J. Geotech. Geoenviron. Eng., 129(1), 12-31. https://doi.org/10.1061/(ASCE)1090-0241(2003)129:1(12).
  31. Michalowski, R.L. and Drescher, A. (2009), "Three-dimensional stability of slopes and excavations", Geotechnique, 59(10), 839-850. https://doi.org/10.1680/geot.8.P.136.
  32. Naeij, M., Ghasemi, H., Ghafarian, D. and Javanmardi, Y. (2021), "Explicit finite element analysis of slope stability by strength reduction", Geomech. Eng., 26(2), 133-146. https://doi.org/10.12989/gae.2021.26.2.133.
  33. Nian, T.K., Jiang, J.C., Wang, F.W., Yang, Q. and Luan, M.T. (2016), "Seismic stability analysis of slope reinforced with a row of piles", Soil Dyn. Earthq. Eng., 84, 83-93. https://doi.org/10.1016/j.soildyn.2016.01.023.
  34. Park, D. and Michalowski, R.L. (2018), "Intricacies in three-dimensional limit analysis of earth slopes", Int. J. Numer. Anal. Methods Geomech., 42(17), 2109-2129. https://doi.org/10.1002/nag.2846.
  35. Rahardjo, H., Lim, T.T., Chang, M.F. and Fredlund, D.G. (1995), "Shear-strength characteristics of a residual soil", Can. Geotech. J., 32(1), 60-77. https://doi.org/10.1139/t95-005.
  36. Rao, P.P., Wu, J., Jiang, G.Y., Shi, Y.W., Chen, Q.S. and Nimbalkar, S. (2021), "Seismic stability analysis for a two-stage slope", Geomech. Eng., 27(2), 189-196. https://doi.org/10.12989/gae.2021.27.2.189.
  37. Ray, R., Deb, K. and Shaw, A. (2019), "Pseudo-Spring smoothed particle hydrodynamics (SPH) based computational model for slope failure", Eng. Anal. Bound. Elem., 101, 139-148. https://doi.org/10.1016/j.enganabound.2019.01.005.
  38. Satyanaga, A., Moon, S.W. and Kim, J.R. (2022), "Stability analyses of dual porosity soil slope", Geomech. Eng., 28(1), 77-87. https://doi.org/10.12989/gae.2021.28.1.077.
  39. Skempton, A.W., Schuster, R.L. and Petley, D.J. (1969), "Joints and fissures in the London Clay at Wraysbury and Edgware", Geotechnique, 19(2), 205-217. https://doi.org/10.1680/geot.1969.19.2.205.
  40. Tran, A.T.P., Kim, A.R. and Cho, G.C. (2019), "Numerical modeling on the stability of slope with foundation during rainfall", Geomech. Eng., 17(1), 109-118. https://doi.org/10.12989/gae.2019.17.1.109.
  41. Ukritchon, B., Yoang, S. and Keawsawasvong, S. (2020), "Undrained stability of unsupported rectangular excavations in non-homogeneous clays", Comput. Geotech., 117, 103281. https://doi.org/10.1016/j.compgeo.2019.103281.
  42. Wang, L., Sun, D.A. and Li, L. (2019), "3D stability of partially saturated soil slopes after rapid drawdown by a new layer-wise summation method", Landslides., 16(2), 295-313. https://doi.org/10.1007/s10346-018-1081-2.
  43. Weng, M.C., Lin, M.L., Lo, C.M., Li, H.H., Lin, C.H., Lu, J.H. and Tsai, S.J. (2019), "Evaluating failure mechanisms of dip slope using a multiscale investigation and discrete element modelling", Eng. Geol., 263, 105303. https://doi.org/10.1016/j.enggeo.2019.105303.
  44. Yang, X.L. and Li, Z.W. (2018), "Comparison of factors of safety using a 3D failure mechanism with kinematic approach", Int. J. Geomech., 18(9), 04018107. https://doi.org/ 10.1061/(ASCE)GM.1943-5622.0001235.
  45. Yang, X.L. and Xu, J.S. (2017), "Three-dimensional stability of two-stage slope in inhomogeneous soils", Int. J. Geomech., 17(7), 06016045. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000867.
  46. Zhang, F., Leshchinsky, D., Baker, R., Gao, Y.F. and Leshchinsky, B. (2016), "Implications of variationally derived 3D failure mechanism", Int. J. Numer. Anal. Methods Geomech., 40(18), 2514-2531. https://doi.org/ 10.1002/nag.2543.
  47. Zhang, H.T., Luo, X.Q., Bi, J.F., He, G.F. and Guo, Z.J. (2019), "Submarine slope stability analysis during natural gas hydrate dissociation", Mar. Geores. Geotechnol., 37(4), 467-476. https://doi.org/10.1080/1064119X.2018.1452997.
  48. Zhang, Y.B., Chen, G.Q., Zheng, L., Li, Y.G. and Zhuang, X.Y. (2013), "Effects of geometries on three-dimensional slope stability", Can. Geotech. J., 50(3), 233-249. https://doi.org/10.1139/cgj-2012-0279.
  49. Zhou, J.F and Qin, C.B. (2020), "A novel procedure for 3D slope stability analysis: lower bound limit analysis coupled with block element method", Bull. Eng. Geol. Environ, 79(4), 1815-1829. https://doi.org/10.1007/s10064-019-01657-1.
  50. Zhou, Y., Zhang, F., and Li, B. (2019), "Static and seismic stability charts for three-dimensional cut slopes and natural slopes under short-term undrained conditions", Adv. Civ. Eng., 2019, 191467. https://doi.org/10.1155/2019/1914674.