DOI QR코드

DOI QR Code

Influence of compaction techniques and cement paste thickness on porous concrete performance

  • Thaman Bahadur Khadka (Department of Civil Engineering, Pulchowk Campus, Tribhuwan University) ;
  • Gokarna Bahadur Motra (Department of Civil Engineering, Pulchowk Campus, Tribhuwan University) ;
  • Bharat Mandal (Department of Civil Engineering, Pulchowk Campus, Tribhuwan University) ;
  • Kshitij C. Shrestha (Department of Civil Engineering, Pulchowk Campus, Tribhuwan University)
  • Received : 2025.06.15
  • Accepted : 2025.12.23
  • Published : 2026.02.25

Abstract

This study investigates the influence of compaction mechanisms and corresponding cement paste thickness on the properties of porous concrete. Using Proctor and Marshall hammers, cylindrical specimens were compacted in both 3-layer and 5-layer configurations with 25 blows per layer. Two aggregate size ranges, 4.75-8.0 mm and 8.0-12.5 mm, were utilized. Experimental evaluations using the both compaction methods demonstrated their effectiveness in producing a uniform mix, as evidenced by consistent measurements of compressive strength, density, porosity, and permeability. While compaction energy influences void structure, cement content has a more significant effect on compressive strength, indicating that optimizing cement content is key to achieving desired strength. MATLAB image analysis showed effective cement paste thickness (d50) ranged from 0.485 mm (Marshall 5-layer) to 0.605 mm (Proctor 3-layer), with over 50% of values below 0.6 mm and a peak at 0.1 mm. Cement paste thickness is primarily controlled by cement content rather than compaction energy and shows a positive correlation with compressive strength. Overall, increasing cement paste thickness enhances strength. Furthermore, a two-factor ANOVA was performed to statistically evaluate the effects of aggregate size and compaction method, confirming that compaction method significantly influences compressive strength, while both factors significantly affect permeability. These results highlight the importance of managing compaction technique, cement paste distribution and aggregate size to balance mechanical performance and permeability in porous concrete design.

Keywords

Acknowledgement

The authors acknowledge the support provided by University Grants Commission, Nepal, Award No. CRG-79/80-Engg-02.

References

  1. Garcia-Fresca, B., Sharp, J.M. (2005). Hydrogeologic considerations of urban development: Urban-induced recharge. The Geological Society of America, 16, 1. https://doi.org/10.1130/2005.4016(11).
  2. Rahman, M., Islam, M.M., Kim, H.J., Sadiq, S., Alam, M., Siddiqua, T., ... Dewan, A. (2023). Assessing the influence of land cover and climate change impacts on runoff patterns using CA-ANN model and CMIP6 data. ISPRS International Journal of Geo-Information, 12(10), 401. https://doi.org/10.3390/ ijgi12100401.
  3. Azad, A., Sheikh, M.N., Hai, F.I. (2024). A critical review of the mechanisms, factors, and performance of pervious concrete to remove contaminants from stormwater runoff. Water Research, 251, 121101. https://doi.org/10.1016/j.watres.2024.121101.
  4. Shang, H., Sun, Z. (2021). Laboratory evaluation of PAHs removal by multi-functional green pervious concrete (MGPC) pavement. Journal of Cleaner Production, 315, 128032. https://doi.org/10.1016/j.jclepro.2021.128032.
  5. Nguyen, D.H., Sebaibi, N., Boutouil, M., Leleyter, L., Baraud, F. (2014). A modified method for the design of pervious concrete mix. Construction and Building Materials, 73, 271-282. https://doi.org/10.1016/j.conbuildmat.2014.09.088.
  6. Moretti, L., Di Mascio, P., Fusco, C. (2019). Porous concrete for pedestrian pavements. Water, 11(10), 2105. https://doi.org/10.3390/w11102105.
  7. Yahia, A., Kabagire, K.D. (2014). New approach to proportion pervious concrete. Construction and Building Materials, 62, 38-46. https://doi.org/10.1016/j.conbuildmat.2014.03.025.
  8. Tran, X.H., Tawie, R. (2014). A systematic approach for the development of porous concrete based on axiomatic design theory. Computers and Concrete, 491-503. https://doi.org/10.12989/cac.2009.6.6.491.
  9. Gupta, R. (2014). Monitoring in situ performance of pervious concrete in British Columbia—A pilot study. Case Studies in Construction Materials, 1, 1-9. https://doi.org/10.1016/j.cscm.2013.10.001.
  10. Elizondo-Martínez, E.J., Andres-Valeri, V.C., Jato-Espino, D., Rodriguez-Hernandez, J. (2020). Review of porous concrete as multifunctional and sustainable pavement. Journal of Building Engineering, 27, 100967. https://doi.org/10.1016/j.jobe.2019.100967.
  11. Hatanaka, S., Mishima, N., Nakagawa, T., Morihana, H., Chindaprasirt, P. (2012). Finishing methods and compressive strength-void ratio relationships of in-situ porous concrete pavement. Computers & Concrete, 10(3), 231-240. https://doi.org/10.12989/cac.2012.10.3.231.
  12. Bonicelli, A., Crispino, M., Giustozzi, F., Shink, M. (2013). Laboratory analysis for investigating the impact of compaction on the properties of pervious concrete mixtures for road pavements. Advanced Materials Research, 723, 409-419. https://doi.org/10.4028/www.scientific.net/AMR.723.409.
  13. Zhong, R., Leng, Z., Poon, C.S. (2018). Research and application of pervious concrete as a sustainable pavement material: a state-of-the-art and state-of-the-practice review. Construction and Building Materials, 183, 544-553. https://doi.org/10.1016/j.conbuildmat.2018.06.131.
  14. Karanth, S.S., Kumar, U.L., Danigond, N. (2019). Porous concrete with optimum fine aggregate and fibre for improved strength. Advances in Concrete Construction, 305-309. https://doi.org/10.12989/acc.2019. 8.4.305.
  15. Sanjaya, N., Saloma, Hanafiah, Juliantina, I., Nurjannah, S.A. (2021). Compressive strength, permeability and porosity analysis of pervious concrete by variation of aggregate and compacting method. Journal of Physics: Conference Series, 1783(1), 012073. https://doi.org/10.1088/1742-6596/1783/1/012073.
  16. Esmail, B.K., Saeed, N.M., Manguri, S.R., Gunal, M. (2024). Engineering properties of pervious concretes produced with recycled aggregate at different aggregate-to-cement ratio. Advances in Concrete Construction, 17(1), 13-26. https://doi.org/10.12989/acc.2024.17.1.013.
  17. Debnath, B., Sarkar, P.P. (2022). Performance of pervious concrete as a sustainable alternative toward green infrastructure using marginal aggregates. Recent advances in civil engineering: Proceedings of the 2nd international conference on sustainable construction technologies and advancements in civil engineering (ScTACE 2021), Singapore, May.
  18. Suleiman, M.T., Kevern, J., Schaefer, V.R., Wang, K. (2006). Effect of compaction energy on pervious concrete properties. Submitted to concrete technology forum-focus on pervious concrete, National Ready Mix Concrete Association, Nashville, TN, May.
  19. Joshaghani, A., Ramezanianpour, A.A., Ataei, O., Golroo, A. (2015). Optimizing pervious concrete pavement mixture design by using the Taguchi method. Construction and Building Materials, 101, 317-325. https://doi.org/10.1016/j.conbuildmat.2015.10.094.
  20. Suleiman, M.T., Kevern, J., Schaefer, V.R., Wang, K. (2006). Effect of compaction energy on pervious concrete properties. Submitted to concrete technology forum-focus on pervious concrete, National ready mix concrete association, Nashville, TN, May.
  21. Wanielista, M., Chopra, M. (2007). Performance assessment of Portland cement pervious pavement. Performance assessment of a pervious concrete pavement as a shoulder for an interstate rest area parking lot.
  22. Sahdeo, S.K., Chandrappa, A., Biligiri, K.P. (2021). Effect of compaction type and compaction efforts on structural and functional properties of pervious concrete. Transportation in Developing Economies, 7(2), 19. https://doi.org/10.1007/s40890-021-00129-0.
  23. Taheri, B.M., Ramezanianpour, A.M. (2021). Optimizing the mix design of pervious concrete based on properties and unit cost. Advances in Concrete Construction, 11(4), 285-298. https://doi.org/10.12989/acc.2021.11.4.285.
  24. Bonicelli, A., Giustozzi, F., Crispino, M., Borsa, M. (2015). Evaluating the effect of reinforcing fibres on pervious concrete volumetric and mechanical properties according to different compaction energies. European Journal of Environmental and Civil Engineering, 19(2), 184-198. https://doi.org/10.1080/19648189.2014.939308.
  25. Ahmed, T., Hoque, S. (2020). Study on pervious concrete pavement mix designs. IOP Conference Series: Earth and Environmental Science, 476(1), 012062. https://doi.org/10.1088/1755-1315/476/1/012062.
  26. Obla, K., Gajanan, S. (2015). Pervious concrete for sustainability development. Pervious Concrete for Sustainable Development, 54-107. https://doi.org/10.1201/b18613-8.
  27. Sahdeo, S.K., Ransinchung, G.D., Rahul, K.L., Debbarma, S. (2020). Effect of mix proportion on the structural and functional properties of pervious concrete paving mixtures. Construction and Building Materials, 255, 119260. https://doi.org/10.1016/j.conbuildmat.2020.119260.
  28. Elizondo-Martinez, E.J., Ossa-Lopez, A., Rodriguez-Hernandez, J. (2021). Evaluation of the effect of different compaction methods on porous concrete pavements: correlation with strength and permeability. Journal of Materials in Civil Engineering, 33(8), 04021184. https://doi.org/10.1061/(asce)mt.1943-5533.0003791.
  29. AlShareedah, O., Haider, M.M., Nassiri, S. (2020). Correlating laboratory and field compaction levels to achieve optimum in situ mechanical properties for pervious concrete pavements. Journal of Materials in Civil Engineering, 32(10), 04020278. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003361.
  30. 522R, ACI Committee (2010). Report on pervious concrete.
  31. ASTM-C150 (2021). iTeh standards iTeh standards i: 1-5.
  32. Khadka, T.B., Motra, G.B., Mandal, B., Shrestha, K.C. (2025). Effect of aggregate size on mechanical behavior and pore structure features of the pervious concrete. Advances in Civil Engineering, 2025(1), 9939241. https://doi.org/10.1155/adce/9939241.
  33. ASTM C127 (2004). Standard test method for density, relative density (Specific gravity), and absorption of coarse aggregate. Annual Book of ASTM Standards 04, 1-5.
  34. IS: 2386 (Part 4) (1963). Methods of test for aggregates for concrete part IV mechanical of indian standards aggregates for concrete. Bureau of Indian Standards, New Delhi, India.
  35. Astm:C29/C29M-09 (2009). Standard test method for bulk density ("Unit Weight") and voids in aggregate. ASTM International I, 1-5.
  36. Ferić, K., Sathish Kumar, V., Romić, A., Gotovac, H. (2023). Effect of aggregate size and compaction on the strength and hydraulic properties of pervious concrete. Sustainability, 15(2), 1146. https://doi.org/ 10.3390/su15021146.
  37. ASTM-C192 (2005). Standard practice for making and curing concrete test specimens in the laboratory. ASTM International 04, 1-6.
  38. ASTM-C1754 (2012). Standard test method for density and void content of hardened pervious concrete. ASTM International.
  39. Lamichhane, R., Motra, G.B., Khadka, T.B., Zhang, Y.X., Pathak, P., Pandit, S. (2024). Impact of water level variation on mechanical properties of porous concrete. Sustainability, 16(9), 3546. https://doi.org/10.3390/su16093546.
  40. Yoon, H.N., Seo, J., Kim, S., Kil, T., Jang, D., Bae, J.H., Lee, H.K. (2021). Sound-absorption and NO x-removal performances of TiO 2-incorporated porous concrete made with bottom ash aggregates. Advances in Concrete Construction, 12(1), 1-11. https://doi.org/10.12989/acc.2021.12.1.001.
  41. ASTM C39/C39M-14 (2005). Standard test method for compressive strength of cylindrical concrete specimens 1. ASTM International I, 1-7.
  42. ASTM-C617 (2009). Standard practice for capping cylindrical concrete specimens 1 98, 1-5.
  43. Torres, A., Hu, J., Ramos, A. (2015). The effect of the cementitious paste thickness on the performance of pervious concrete. Construction and Building Materials, 95, 850-859. https://doi.org/10.1016/j.conbuildmat.2015.07.187.
  44. Yu, F., Sun, D., Wang, J., Hu, M. (2019). Influence of aggregate size on compressive strength of pervious concrete. Construction and Building Materials, 209, 463-475. https://doi.org/10.1016/j.conbuildmat. 2019.03.140.
  45. Liu, T., Wang, Z., Zou, D., Zhou, A., Du, J. (2019). Strength enhancement of recycled aggregate pervious concrete using a cement paste redistribution method. Cement and Concrete Research, 122, 72-82. https://doi.org/10.1016/j.cemconres.2019.05.004.
  46. Wang, Z., Zou, D., Liu, T., Zhou, A. (2021). Influence of paste coating thickness on the compressive strength, permeability, and mesostructure of permeable concrete. Construction and Building Materials, 299, 123994. https://doi.org/10.1016/j.conbuildmat.2021.123994.
  47. Ni, T., Ma, W., Yang, Y., Yu, J., Liu, J., Jiang, C., Gu, C. (2021). Interface reinforcement and a new characterization method for pore structure of pervious concrete. Construction and Building Materials, 267, 121052. https://doi.org/10.1016/j.conbuildmat.2020.121052.
  48. Xiong, B., Gao, H., Chen, J., Lu, X., Tian, B., Chen, B., Liu, W. (2023). Study on influencing factors of paste coating thickness of pervious concrete. Buildings, 13(2), 380. https://doi.org/10.3390/buildings13020380.
  49. Xie, X., Zhang, T., Yang, Y., Lin, Z., Wei, J., Yu, Q. (2018). Maximum paste coating thickness without voids clogging of pervious concrete and its relationship to the rheological properties of cement paste. Construction and Building Materials, 168, 732-746. https://doi.org/10.1016/j.conbuildmat.2018.02.128.
  50. Putman, B.J., Neptune, A.I. (2011). Comparison of test specimen preparation techniques for pervious concrete pavements. Construction and Building Materials, 25(8), 3480-3485. https://doi.org/10.1016/j.conbuildmat.2011.03.039.
  51. Chindaprasirt, P., Hatanaka, S., Chareerat, T., Mishima, N., Yuasa, Y. (2008). Cement paste characteristics and porous concrete properties. Construction and Building Materials, 22(5), 894-901. https://doi.org/10.1016/j.conbuildmat.2006.12.007.
  52. Sha, F., Zhang, S.M., Sun, X.C., Fan, G.X., Diao, Y., Duan, X.F., Wang, H. (2024). Mechanical performance and pore characteristics of pervious concrete. Case Studies in Construction Materials, 21, e03674. https://doi.org/10.1016/j.cscm.2024.e03674.
  53. Fu, T.C., Yeih, W., Chang, J.J., Huang, R. (2014). The influence of aggregate size and binder material on the properties of pervious concrete. Advances in Materials Science and Engineering, 2014(1), 963971. http://ddoi.org/10.1155/2014/963971.
  54. Rao, Y., Ding, Y., Sarmah, A.K., Liu, D., Pan, B. (2020). Vertical distribution of pore-aggregate-cement paste in statically compacted pervious concrete. Construction and Building Materials, 237, 117605. https://doi.org/10.1016/j.conbuildmat.2019.117605.