• 한국자동차공학회논문집
• /
• 제6권5호
• /
• pp.153-161
• /
• 1998

The knock in a spark ignition engine has been investigated to avoid the damage to the engine and unpleasant feeling caused by the pressure waves propagating across the combustion chamber. Knock intensity and knock onset angle were used as physical parameters to quantify the knock characteristics. The knock intensity is defined as a peak to peak value of the bank pass filtered combustion pressure signal and the knock onset angle is determined as the crank angle at which this signal exceeded the threshold level on each cycle. The cyclic variation of knock in four valve single cylinder engine was investigated with these two parameters. The location of autoignition was also examined by ion probes in the cylinder head gasket and squish region in the combustion chamber. For this measurement, a single cylinder engine was modified to accept the pressure transducer, 18 ion probes in the squish region and 8 ion probes in the specially designed PCB (Printed \ulcornerCircuit Board) cylinder head gasket.

• 한국자동차공학회논문집
• /
• 제5권1호
• /
• pp.186-194
• /
• 1997

The objective of this study is to develope knock control algorithms which can increase engine power without causing frequent knock occurrence. A four cylinder spark-ignition engine is used for the experiments to develop knock control algorithms which use block vibration signals. Knock occurrence is detected accurately by using knock threshold values which consider the difference of transmission path of each cylinder. Spark timing is controlled both simultaneously and individually. With the simultaneous control, torque gain is achieved by retarding the spark timing on knock occurrence in propotion to the knock intensity. The individual knock control algorithm results in higher torque gain than the simultaneous knock control algorithm. The knock occurrence frequency of the individual knock control algorithm is about twice the value of the simultaneous knock control algorithm results. Both control algorithms give similar torque gain of about 3% when they are optimized.

• 오토저널
• /
• 제14권5호
• /
• pp.30-40
• /
• 1992

Spark knock obstructs any improvement in the efficiency and performance of an engine. As the knock mechanism of spark ignition engine, the detonation and the autoignition theory have been offered. In this paper, the knock model was established, which was able to predict the onset of knock and knock timing of spark ignition engine by the basis of autoignition theory. This model was a function of engine speed and equivalent air-fuel ratio. When this established knock model was tested from 1000rpm to 3000rpm of engine speed data, maximum error was crank angle 2 degrees between measured and predicted knock time. And the main results were as follows by the experimental analysis of spark knock in spark ignition engine. 1) Knock frequency was increased as engine speed increased. 2) Knock amplitude was increased as mass of end gas increased. 3) Knock frequency was occured above minimum 18% mass fraction of end gas.

• 오토저널
• /
• 제14권5호
• /
• pp.61-68
• /
• 1992

Knock phenomenon is an abnormal combustion originated from autoignition of unburned gas in the end-gas region during the later stage of combustion process and it accompanys a high pitched metallic noise. Engine Knock is accompanied with a vibration of engine cylinder and when it is severe, it can cause major engine demage. Engine Knock is characterized in terms of knock crank angle, knock pressure, pressure jump and knock intensity. In this study, a 4-cylinder spark ignition engine was used for experiment and eighty consecutive cycles were analyzed statistically. The purpose of this study is to characterize spark ignition engine knock as a function of ignition timing and fuel research octane number. The result of this study can be summerized as follows. Knock occurrence angle approached TDC as ignition timing is advanced. Pressure and knock intensity gradually increased as spark timing is advanced. Mean knock occurence angle gradually approached TDC as fuel research octane number is decreased for identical spark timing. Knock intensity increased linearly as RON is decreased.

• Reproductive and Developmental Biology
• /
• 제41권1호
• /
• pp.7-16
• /
• 2017

The knock-in efficiency in the fibroblast is very important to produce transgenic domestic animal using nuclear transfer. In this research, we constructed three kinds of different knock-in vectors to study the efficiency of knock-in depending on structure of knock-in vector with different size of homologous arm on the ${\beta}-casein$ gene locus in the somatic cells; DT-A_cEndo Knock-in vector, DT-A_tEndo Knock-in vector I, and DT-A_tEndo Knock-in vector II. The knock-in vector consists of 4.8 kb or 1.06 kb of 5' arm region and 1.8 kb or 0.64 kb of 3' arm region, and neomycin resistance gene(neor) as a positive selection marker gene. The cEndo Knock-in vector had 4.8 kb and 1.8 kb homologous arm. The tEndo Knock-in vector I had 1.06 kb and 0.64 kb homologous arm and tEndo Knock-in vector II had 1.06 kb and 1.8 kb homologous arm. To express endostatin gene as transgene, the F2A sequence was fused to the 5' terminal of endostatin gene and inserted into exon 7 of the ${\beta}-casein$ gene. The knock-in vector and TALEN were introduced into the bovine fibroblast by electroporation. The knock-in efficiencies of cEndo, tEndo I, and tEndo II vector were 4.6%, 2.2% and 4.8%, respectively. These results indicated that size of 3' arm in the knock-in vector is important for TALEN-mediated homologous recombination in the fibroblast. In conclusion, our knock-in system may help to create transgenic dairy cattle expressing human endostatin protein via the endogenous expression system of the bovine ${\beta}-casein$ gene in the mammary gland.

• 한국자동차공학회논문집
• /
• 제7권9호
• /
• pp.28-35
• /
• 1999

In this study, investigation of transient knock characteristics in a spark-ignition engine has been carried out. The universal knock threshold values were found by a DFDD method and a NSDBP method which is a non-dimensional version of the SDBP method. Also modified NSDBP method could be used for transient knock detection. In a commercial ECU , spark timing was retarded from the steady -state spark timing during rapid throttle opening to avoid uncomfortable feeling and knock. Knock usually occurred just after the start of rapid throttle opening when spark timing was set, as values for the steady state condition. We found that air/fuel ratio deeply involved with the knock during transient condition. Due to the difference of initial heat release rate, knock occurred more easily at rich air/fuel ratio than at lean air/fuel ratio.

• Reproductive and Developmental Biology
• /
• 제32권3호
• /
• pp.205-209
• /
• 2008

본 연구는 돼지 $\beta$-casein 유전자 위치에서 EGFP가 발현될 수 있는 knock-in 벡터를 구축하기 위하여 실시되었다. 돼지의 $\beta$-casein 유전자를 이용하여 knock-in 벡터를 구축하기 위해 돼지의 태아 섬유아세포로부터 $\beta$-casein 유전자를 동정하였고 EGFP, SV4O polyA signal을 동정하였다. Knock-in 벡터는 5' 상동 영역 약 5 kb와 3' 상동 영역 약 2.7 kb로 구성되어있으며, positive selection marker로 $neo^{r}$ 유전자를, negative selection marker로 DT-A 유전자를 사용하였다. 구축된 knock-in 벡터로부터 EGFP의 발현을 확인하기 위하여 생쥐 유선 세포인 HC11 세포에 knock-in 벡터를 도입하였다. 그 결과 EGFP의 발현을 HC11 세포에서 확인하였다. 이와 같은 결과로서 이 block-in 벡터는 knock-in 형질전환 돼지를 생산하는데 사용될 수 있을 것으로 생각된다.

• 오토저널
• /
• 제13권6호
• /
• pp.57-64
• /
• 1991

Spart-ignition engine knock is an abnormal combustion phenomenon originated from auto- ignition of a portion of or the entire end-gas during the later stage of combustion process. And engine knock is accompanied by a vibration of engine cylinder block and a high-pitched metallic noise. Engine knock is characterized in terms of its intensity, its occurrence crank angel and the percentage of engine knock cycles. To characterize engine knock, a precise measurements of cylinder pressure and a statistical analysis of cylinder pressure data are needed. The purpose of this study is to develope a technique to measure engine knock and its characteristics as a function of ignition timing change. A 4-cylinder spark-ignition engine and unleaded gasoline, whose octane number was 94, were used for experiments. To measure engine knock and to analyze engine knock characteristics, cylinder pressure data were sampled by a high speed data acquisition system which was developed in this study. Cylinder pressure data were sampled at each 0.1.deg. crank angle and the number of cycles continuously sampled was 80.

• Asian-Australasian Journal of Animal Sciences
• /
• 제25권10호
• /
• pp.1473-1480
• /
• 2012

The Galactose-${\alpha}1$,3-galactose (${\alpha}1$,3Gal) epitope is responsible for hyperacute rejection in pig-to-human xenotransplantation. Human decay-accelerating factor (hDAF) is a cell surface regulatory protein that serves as a complement inhibitor to protect self cells from complement attack. The generation of ${\alpha}1$,3-galactosyltransferase (GGTA1) knock-out pigs expressing DAF is a necessary step for their use as organ donors for humans. In this study, we established GGTA1 knock-out cell lines expressing DAF from pig ear fibroblasts for somatic cell nuclear transfer. hDAF expression was detected in hDAF knock-in heterozygous cells, but not in normal pig cells. Expression of the GGTA1 gene was lower in the knock-in heterozygous cell line compared to the normal pig cell. Knock-in heterozygous cells afforded more effective protection against cytotoxicity with human serum than with GGTA1 knock-out heterozygous and control cells. These cell lines may be used in the production of GGTA1 knock-out and DAF expression pigs for xenotransplantation.

• 한국자동차공학회논문집
• /
• 제1권3호
• /
• pp.12-21
• /
• 1993

In recent years, high efficiency, high performance, and low pollutant emmision engines have been developed. Knock phenomenon has drawn interests because it became an hinderance to engine power and efficiency increase through higher compression ratio. Knock phenomenon is an abnormal combustion originated from autoignition of unburned gas in the end-gas region during the later stage of combustion process and accompanied a high pitched metallic noise. And this phenomenon is characterized by knock occurrence percentage, knock occurrence angle and knock intensity. A four cylinder spark ignition engine is used in our experiment, and its combustion chamber pressure is measured at various engine speeds, ignition timing. The data are analyzed by numerous methods in order to select the optimum methods and to achieve better understanding of knock characteristics. Methods using band-pass filter, third derivative and step method are shown to be the most suitable, while methods using frequency analysis are shown to be unsuitable. Because step method only uses signals above threshold value during knocking condition, pressure signal analyses with this method show good signal-to-noise ratio.