• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.2
• /
• pp.514-525
• /
• 1996

In this paper, Push-push Osciplier(Oscillator + Multiplier) has been analyzed by even-odd mode analysis method. A 10GHz DRO, an Osciplier using 10GHz DRO design method and an Osciplier using even-odd mode analysis method were designed, fabricated and tested to verify this method. The measured results verified the validity of the analysis method using even-odd mode analysis.

• Journal of electromagnetic engineering and science
• /
• v.17 no.2
• /
• pp.86-90
• /
• 2017

In this study, a novel third-order bandpass filter, which is based on a rectangular closed loop resonator, is presented. By adding a series resonator to the conventional loop resonator, the resonator's even resonant mode is split into two modes, while the odd resonant mode is not affected. Therefore, by varying the values of the series resonator elements, the resonant frequencies of two even modes can be determined independent of the odd-mode resonant frequency. In the proposed triple-mode filter design, instead of using a lumped series resonator, a T-shaped transmission line is coupled to the resonator via a small gap. To verify the design method, a filter is designed at 2.4 GHz with a bandwidth of 100 MHz. The improved performances of the proposed triple-mode filter are compared with those of the conventional dual mode filter.

• Transactions of the Society of Information Storage Systems
• /
• v.6 no.1
• /
• pp.6-11
• /
• 2010

Researches for actuator which is appropriate to slim optical disk drive (ODD) have been progressed for a long time. Various types of actuators are suggested to secure high performances with slim thickness. In this paper, the slim actuator with symmetric electromagnetic (EM) circuit is suggested to apply slim ODD. Various EM circuits are proposed to increase EM force in the focusing and the tracking directions. Flexible mode frequencies and driving sensitivities are increased by using stress distribution and design of experiment (DOE). Consequently, final model is suggested to have high flexible mode frequencies and driving sensitivities.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.3
• /
• pp.553-559
• /
• 1994

A coupled microstrip-slot line is analyzed using a full wave method in the specral domain. The characteristics of the coupled microstrip-slot line are obtained based on the Galerkin`s method. The characteristics of even mode by microstrip line and odd mode by slot line are calculated respectively. Especially the singularity of basis function is enforced to be considered with respect of modes. Numerical results are compared with available data and shown good agreement.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.5
• /
• pp.238-242
• /
• 2001

In this paper, we extracted design parameters for re-entrant mode microstrip directional coupler using FE(finite element) calculations. The microstrip directional coupler suffers from a poor directivity due to effect of the inhomogeneous dielectric including both dielectric substrate and air in microstrip transmission lines. Thus, the phase velocity of even mode is not equal to that of odd mode. In order to improve the directivity of microstrip directional coupler, a novel re-entrant mode microstrip directional coupler was employed. In microstrip configuration, the high directivity can be reached by matching the even- and odd-mode effective phase velocities. Through the values of capacitance obtained from 2-dimensional FE calculations, the phase velocities for each mode and the design parameter were extracted for the proposed parallel coupled-line configuration. Based on the extracted design parameter with phase matching condition, we designed and fabricated a 30dB directional coupler at 0.85GHz. Experimental results show good performance with excellent, isolation and directivity.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.4 no.2
• /
• pp.122-129
• /
• 2001

A characterization procedure for analyzing symmetric coupled MIS(Metal-Insulator-Semiconductor) transmission line is used the same procedure as a general single layer symmetric coupled line with perfect dielectric substrate from the extraction of the characteristic impedance and propagation constant for even- and odd-mode. In this paper, an analysis for a new substrate shielding symmetric coupled MIS structure consisting of grounded crossbar at the interface between Si and SiO2 layer using the Finite- Difference Time-Domain(FDTD) method is presented. In order to reduce the substrate effects on the transmission line characteristics, a shielding structure consisting of grounded crossbar lines over time-domain signal has been examined. Symmetric coupled MIS transmission line parameters for even- and odd-mode are investigated as the functions of frequency, and the extracted distributed frequency- dependent transmission line parameters and corresponding equivalent circuit parameters as well as quality factor for the new MIS crossbar embedded structure are also presented. It is shown that the quality factor of the symmetric coupled transmission line can be improved without significant change in the characteristic impedance and effective dielectric constant.

• Journal of the Korean Institute of Navigation
• /
• v.25 no.2
• /
• pp.131-136
• /
• 2001

A new analysis method of lumped-element directional coupler for CATV was proposed, where the even-and odd-mode theory for a symmetrical coupled-line directional coupler was applied to a transformer-type directional coupler. In addition, the tap-offs were analyzed by the proposed theory, which are widely used in CATV (Cable Television) systems. By comparing the calculated results for S-parameters results to the measured ones using only the even-and odd-mode reflection coefficients, the validity of the proposed analysis method was confirmed. Then, it was clearly shown that the tap-off has very wide bandwidth from 5 MHz to 4,000 MHz by adopting the proposed theory.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.12
• /
• pp.1321-1328
• /
• 2003

In this paper, we demonstrate that the directivity of the CPW(Coplanar Waveguide) directional coupler with finite-extent backed conductor is enhanced by eliminating center region of backed conductor appropriately. If the backed conductor is removed at center region of couplers, the couplers have two backed conductors. If effective odd mode dielectric constant is decreased at center region, the electrical length for odd mode is changed and phase velocity is same at the directional couplers. Hence, directivity is improved. The eliminated length is solved by an odd and even mode analysis. The designed moderate CPW directional coupler with the proposed compensation structure has excellent directivity and matching characteristic at center frequency in simulation and measurement.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.346-351
• /
• 2001

A new analysis method was proposed, where the even . odd-mode theory for a symmetrical coupled-line directional coupler was applied to a transformer-type directional coupler. In addition, the tap-offs were analyzed by the proposed theory, which are widely used in CATV (Cable Television), DBS (Direct Broad- casting Satellite), CS (Communication Satellite) systems. By comparing the calculation results to the measured ones using the even . odd-mode reflection coefficients only, the validity of the proposed analysis method was confirmed. Then, the tap-off has been broadened from 5 MHz over 4,000 MHz by adopting the proposed theory.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.775-779
• /
• 2001

In optical disk drive (ODD), disk rotation speed has been increasing rapidly to achieve high data transfer rate. High servo bandwidths for focusing and tracking actuator are required to follow dynamic disturbance by high rotation speed in ODD. However, the servo bandwidth is significantly limited by some vibration modes which are induced by the flexibility of moving part. In this work, the vibration modes affecting bandwidth of actuators are suppressed by modifying actuating force by VCM. For this, the relation between the horizontal component of the actuating force and vibration mode is analyzed and force characteristic affecting to vibration mode is obtained through electromagnetic and structural analysis using simulation program.