• 한국안전학회지
• /
• 제13권3호
• /
• pp.11-23
• /
• 1998

In this study, collapse test of thin-walled structure is performed under axially quasi-static and impact load in collapse characteristic to develop the optimum structural member for a light-oriented automobile. Furthermore, the energy-absorbing capacity is observed according to the variety of configuration(circular, square), aspect ratio in aluminum specimen to obtain basic data for the improved member of vehicle. In both quasi-static and impact collapse test, Al circular specimens collapse, in general, with axisymmetric mode in case of thin thickness while collapse with non-axisynmetric mode according to the thickness increase. For Al rectangular specimens, they collapse with axisymmetric mode in case of thin thickness, with mixed collapse mode according to the increase of thickness. In terms of initial max. load, Al square specimen turns out the best member among specimens, and then Al square, circular and circular with large scaling ratio, respectively. In case of quasi-static compression test, the absorbed energy per unit volume and mass shows higher in Al circular specimen, and then Al square, circular with large scaling ratio, respectively, according to shape ratio the absorbed energy per unit volume and mass in case of max. impact compression load is higher than that of static load. But the absorbed energy per unit volume and mass shows that Al circular specimen is the best member. Especially, unlike max. compression loan, the absorbed energy per unit volume and mass in impact test turns out the low value.

• 한국산림과학회지
• /
• 제4권1호
• /
• pp.26-29
• /
• 1965

1) 본시험(本試驗)은 area sampling의 Form과 unit의 크기를 결정(決定)짓고져 행(行)하여진 실험(實驗)이다. 2) unit가 작은 것은 큰것에 비(比)해 과대추정치(過大推定値)를 주었다. 3) incular sample plot는 타(他)에 비(比)하여 과대추정치(過大推定値)를 준다. 4) area sampling에 있어서는 rectangular plot $0.06ha(20m{\times}30m)$가 가장 경제적(經濟的) unit가 된다. 또 circular plot를 사용(使用)할 때는 0.10 ha, square plot를 사용(使用)할 때는 0.08ha 보다 큰 unit를 사용(使用)해야만 population mean과 유의차(有意差)없어 추정(推定)할 수 있다.

• 설비공학논문집
• /
• 제26권2호
• /
• pp.67-71
• /
• 2014

In this study, a fan coil unit with an oval-type heat exchanger has been developed. The performance of the present fan coil unit has been investigated, by comparison with the previous fan coil unit with a circular-type heat exchanger. For the fan coil unit with circular- and oval-type heat exchangers, the heat flux and pressure loss through the heat exchangers were measured at standard operating conditions. In addition, the wind speeds exhausted from the fan coil units were compared, for the same fan motor operation. The experimental results show that the average wind speed of the oval-type heat exchanger is 20 percent higher than that of the circular-type heat exchanger. The heat flux in the oval-type heat exchanger is enhanced by 40% or more, over the circular-type heat exchanger.

• Journal of the Korean Data and Information Science Society
• /
• 제23권4호
• /
• pp.797-805
• /
• 2012

Many circular distributions are known to be not only asymmetric but also bimodal. Hidden truncation method of generating asymmetric distribution is applied to a bivariate circular distribution to generate an asymmetric circular distribution. While many other existing asymmetric circular distributions can only model an asymmetric data, this new circular model has great flexibility in terms of asymmetry and bi-modality. Some properties of the new model, such as the trigonometric moment generating function, and asymptotic inference about the truncation parameter are presented. Simulation and real data examples are provided at the end to demonstrate the utility of the novel distribution.

• 한국정밀공학회지
• /
• 제16권9호
• /
• pp.172-178
• /
• 1999

3D linear and circular interpolations are a basic part for the machining of complex shapes. Until now, because of the absence of appropriate algorithms for the generation of 3D lines and circles, a full accomplishment for available machine tool resolution is difficult. this paper presents new algorithms for 3D linear and circular interpolation in the reference pulse technique. In 3D space, the line or circle is not expressed as an implicit function, it is only defined as the intersection of two surfaces. A 3D line is defined as the intersection of two planes, and a 3D circle is defined as the intersection of a plane and the surface of a sphere. Based on these concepts, interpolation algorithms are designed to follow intersection curves in 3D space, and a real-time 3D linear and circular interpolator was developed in software using a PC. The algorithm implemented in a PC showed promising results in interpolation error and speed performance. It is expected that it can be applied to the next generation computerized numerical control systems for the machining of 3D lines, circles and some other complex shapes.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1999년도 학회창립 10주년 기념 1999년도 가을 학술발표회 논문집
• /
• pp.21.2-274
• /
• 1999

This study aims to examine the influence of the unit powder content of concrete and the fine aggregate ration of high flowing concrete after the improvement of grain shape of the coarse aggregate. According to the experimental results, flowbility and compating of concrete presents the best states in the S/a which has the smallest void ratio. The coarse aggregate after improvement of grain shape has been changed from 0.68 circular ratio of disc shape to 0.73 circular shape. It lead to be down 6% of fine aggregate ratio (from 47% to 41%), which is satisfactory to compacting. Also, the improvement of grain shape of the coarse aggregate lead the lowest unit powder content to be down 60kg/㎥ from (530kg/㎥ to 470kg/㎥). And about 11% unit water content can be reduced as unit powder conent is down.

• 대한전자공학회논문지SD
• /
• 제46권7호
• /
• pp.47-52
• /
• 2009

H.264 영상 압축 표준은 높은 압축률과 화질로 널리 이용되고 있다. 이러한 H.264 복호기에서 움직임 보상기는 가장 연산 시간이 오래 걸리고 복잡한 유닛이다. 이러한 움직임 보상기의 성능은 보간 연산기와 참조 픽셀을 외부에서 읽어 오는 동작의 효율성에 의해 결정된다. 따라서 고성능 보간 연산기를 설계하고 참조 메모리와 데이터의 관리를 통해 데이터 재활용을 늘려 외부 메모리 접근 횟수를 줄이는 것이 필요하다. 본 논문에서는 2 차원 회전 레지스터 파일과 움직임 벡터 예측기, 그리고 저복잡도 고성능의 보간 연산기를 이용한 효율적인 움직임 보상기 구조를 제안한다. 2 차원 회전 레지스터는 참조 메모리에서 읽어 온 픽셀 데이터를 보관하면서 보간 연산기에 필요한 픽셀 데이터를 신속하게 공급하고 재활용될 데이터를 효과적으로 처리할 수 있는 기능을 가지고 있다. 제안된 구조에 따라 움직임 보상기를 설계하고 인트라 예측기와 통합하여 예측 연산기를 구현하여 동작과 성능을 검증하였다.

• Journal of Theoretical and Applied Mechanics
• /
• 제1권1호
• /
• pp.89-96
• /
• 1995

An analytical method is presented for predicting the effect of a local deviation in the form of a concentrated mass along a radial line on the free bending vibration characteristics of a nearly axisymmetric circular plate. The approach is based on the Rayleigh-Ritz method and the expression of local deviation of the concentrated radial mass as the variation of heaviside unit step function. The effects of the concentrated mass on the natural frequencies and mode shapes of the plate are predicted with a proposed nondimensional mass parameter.

• 설비공학논문집
• /
• 제24권7호
• /
• pp.560-566
• /
• 2012

Numerical study has been carried out to investigate heat transfer and pressure drop characteristics for streamlined shape tubes. The flow and thermal fields are investigated with varying diameter ratio of the tube ranging from 0.4 to 2.5 and Reynolds number ranging from 10,000 to 30,000. The results show that heat transfer per unit fan power is maximum at $D_2/D_1=0.8$. Furthermore, the heat transfer per unit fan power of streamlined shape tubes was compared with circular tube. The heat transfer per unit fan power of streamlined shape tube was larger than that of circular tube.

• 한국정보통신학회논문지
• /
• 제4권1호
• /
• pp.59-65
• /
• 2000

This paper describes the characteristics of a one dimensional narrow-wall slotted waveguide array with a single-layer linear-to-circular polarization converter consisting of a dipole array. An external boundary value Problem of one slot and three dipoles, which approximates the mutual coupling between the dipole array and an edge slot extending over three faces of a rectangular waveguide, is formulated and analyzed by the method of moments; design of polarization conversion is conducted for this model as a unit element. If every unit element has perfect circular polarization, grating lobes appear in the array pattern due to the alternating slot angle: these are suppressed in this paper by changing the dipole angle and degrading the axial ratio of the unit element. The validity of the design is confirmed by the measurements. The dipole array has negligible effects upon slot impedance; the polarization conversion for existing narrow-wall slotted arrays is realized by add-on dipole array.