• 한국지반공학회논문집
• /
• 제34권4호
• /
• pp.13-25
• /
• 2018

앵커가 보강된 비탈면에 활동이 발생한 경우에는 활동면을 따라 전단면에 전단응력과 휨 응력이 작용하게 되고, 전단변형의 증가는 앵커의 긴장력 변화를 야기한다. 본 연구에서는 전단에 따른 앵커의 긴장력 변화를 확인하기 위해 앵커의 수직방향으로 전단변형을 유발하여 앵커의 긴장력을 측정하는 방법으로 대형 직접전단시험기를 통해 전단시험을 수행하였다. 전단시험은 앵커 설치 유무, 정착부에서 전단면까지의 이격거리(1D, 2D, 4D) 및 측압(0.1MPa, 0.2MPa)을 변수로 총 8가지 조건에 대해 시험을 실시하였다. 전단시험 결과, 이격거리와 주변지반의 측압은 앵커가 설치된 모형 지반의 전단력 및 앵커의 긴장력에 영향을 미치는 것으로 나타났으며, 전단력 변화는 앵커 두부 및 선단부의 축력변화와 관련이 있음을 규명하였다. 따라서 앵커 두부에서의 긴장력 변화 경향을 분석함으로써, 간접적으로 앵커 정착부에서의 전단변형에 따른 거동을 예측할 수 있음을 확인하였다.

• Steel and Composite Structures
• /
• 제21권2호
• /
• pp.357-371
• /
• 2016

Column base connections are critical components in steel structures because they transfer axial forces, shear forces and moments to the foundation. Exposed column bases are quite commonly used in low- to medium-rise buildings. To investigate shear transfer in exposed column base plates, four large scale specimens were subjected to a combination of axial load (compression or tension) and lateral shear deformations. The main parameters examined experimentally include the number of anchor rod, arrangement of anchor rod, type of lateral loading, and axial force ratio. It is observed that the shear resisting mechanism of exposed column base changed as the axial force changed. When the axial force is in compression, the resisting mechanism is rotation type, and the shear force will be resisted by friction force between base plate and mortar layer. The specimens could sustain inelastic deformation with minimal strength deterioration up to column rotation angle of 3%. The moment resistance and energy dissipation will be increased as the number of anchor rods increased. Moreover, moment resistance could be further increased if the anchor rods were arranged in details. When the axial force is in tension, the resisting mechanism is slip type, and the shear force will be resisted by the anchor rods. And the shear resistance was reduced significantly when the axial force was changed from compression to tension. The test results indicated that the current design approach could estimate the moment resistance within reasonable acceptance, but overestimate the shear resistance of exposed column base.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.464-470
• /
• 2005

The numerical analysis is carried out to identify the influence of design factors to shear capacity of cast-in-place (CIP) anchor in ACI 349 Code that is available for the design of fastening system at Nuclear Power Plant (NPP) in this study. The MASA program is used to develop the numerical analysis model and the developed numerical analysis model is verified on a basis of the various test data of CIP anchor. Both $l/d_o$ and $c_1/l$ we considered as design factors. As a result, the variation of $l/d_o$ has no influence on the shear capacity of CIP anchor but $c_1/l$ has a large influence on the shear capacity of CIP anchor, Therefore, it is proved that ACI 349 Code may give a non-conservative results compared with real shear capacity of CIP anchor according to $c_1/l$.

• Computers and Concrete
• /
• 제33권4호
• /
• pp.373-384
• /
• 2024

In this study, a novel mountain train system was developed that can run along a steep gradient of 180 ‰ and sharp curve with a minimum radius of 10 m. For this novel mountain train, an embedded precast concrete rack rail track was implemented to share the track with an automobile road and increase constructability in mountainous regions. The embedded rack rail track is connected to a hydraulically stabilized base (HSB) layer with shear anchors, which must have sufficient longitudinal resistance because they bear most of the traction forces originated from the rack rail and longitudinal loads owing to the steep gradient. In addition, the damage to the shear anchor parts, including the surrounding concrete, must be strictly limited under the service load because the maintenance of shear anchors inside the track is extremely difficult after installation. In this study, the focus was made on the shear anchor behavior and design an embedded rack rail track, considering the serviceability and ultimate limit states. Accordingly, the design loads for mountain trains were established, and the serviceability criteria of the anchor were proposed. Subsequently, the resistance and damage of the shear anchors were evaluated and analyzed based on the results of several finite element analyses. Finally, the design method of the shear anchors for the embedded rack rail track was established and verified.

• 도시과학
• /
• 제7권2호
• /
• pp.29-36
• /
• 2018

The demand for reinforcement in accordance with remodeling, seismic retrofit, and change of use of the existing structure is increasing. Originally, shear wall new and extension method has been adopted a lot as seismic retrofit methods. Recently, dry seismic retrofit method that uses structural steel is mostly adopted in order to minimize spatiotemporal aspect and underpinning that occurs when a construct shear wall. We redesigned the form of old and new concrete joint high-shear ring anchor that was developed according to recent reinforcement method and determined construction method. Shear tests were performed on High-Shear Ring Anchor for steel-concrete connection. Comparison with 4 tests shows that the average of test-to-prediction ratios is 1.01.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 가을 학술발표회 논문집
• /
• pp.621-628
• /
• 2002

Compaction Grouting Pack (CGP) Anchor which is composite anchor of bearing plus friction-type was chosen and executed for the open-cuts in soft ground. This paper presents an analysis of data from tests on composite-anchor by jacking force. The properties of composite-anchor was presented to be as follows , the maximum plastic displacement was 60 mm in abandoned coal fill deposit, the shear stress($\tau$) is expressed as $\tau$ = (equation omitted) kg/$\textrm{cm}^2$ in clayey silt.

• KCI Concrete Journal
• /
• 제12권1호
• /
• pp.91-99
• /
• 2000

A new type of retrof=t anchor bolt that uses deformed reinforcing bars and a commercial adhesive was developed and then an experimental study was carried out to determine the behavior of the anchors in direct shear. The steel-to-concl몫ete interface was tested. Plain concrete slabs with about 20-MPa compressive strength were used for 23 direct shear tests performed Test variables were anchor diameters (D16, D22. and D29) and edge effect. Three different shear tests were completed: simple shear, edge shear where anchors were pulled against the concrete core, and edge shear where anchors were pushed against the concrete cover In the simple and the edge shear tests where the anchors were pulled against the core, the theoretical dowel strength determined by (equation omitted) was achieved but with relatively large displacements. The shear resistances increased with the increasing displacements. In the edge shear test where the anchors were pushrd against the cover, the peak shear strengths signif=cantly lower than the theoretical dowel strength were determined due to cracks developed in concrete when the edge distance was 80 mm. The peak strengths were about 50% of the dowel strength for Dl6 bar. and about 25% or less of the dowel strength for D22 and D29 bars. Test results revealed that the edge shear where the anchor was pushed against the cover controled.

• 한국방재학회 논문집
• /
• 제5권1호
• /
• pp.69-76
• /
• 2005

본 연구는 익스팬션(고하중 앵커와 웨지앵커)의 내력평가 하기 위한 실험적 연구이다. 하중조건은 인발, 전단 및 인발과 전단의 조합하중이다. 고하중 앵커와 웨지 앵커는 국내산 앵커를 사용하였으며, 무근콘크리트에 매입하였다. 앵커 파괴 및 콘크리트 파괴모드에 따른 기존의 앵커 설계식를 연구하였으며, 실험결과를 인발 및 전단내력의 상호작용에 관한 여러 모델들과 비교 분석하였다. 연구결과 다음과 같은 결론을 얻었다. 조합하중 작용 시 힘의 상호작용은 타원형 상호관계가 가장 적합한 것으로 판단된다.

• 대한토목학회논문집
• /
• 제34권2호
• /
• pp.367-375
• /
• 2014

최근 콘크리트 구조물의 보수 보강 및 리모델링 시 구조부재를 부착시키거나 고정하는데 있어서 시공의 유연성 및 용이성으로 후설치 앵커의 사용량이 증가하고 있는 실정이다. 전단하중을 받는 앵커는 강재와 콘크리트의 강도, 연단거리, 앵커간격 등에 따라 다양한 파괴모드를 보이며 대표적인 파괴모드는 강재 파괴, 콘크리트 파열 파괴, 콘크리트 프라이 아웃 파괴 등으로 나타난다. 본 연구에서는 매입깊이, 앵커간격, 연단거리 및 콘크리트 강도를 변수로 한 세트앵커의 전단 실험을 통하여 콘크리트에 매입된 후설치 앵커의 전단 파괴거동에 미치는 영향을 규명하는 것을 그 목적으로 한다. 매입깊이 변수의 실험 결과 매입깊이가 얕을수록 콘크리트 강도의 영향이 큰 것으로 나타났다. 앵커간격 변수의 실험 결과 모두 강재 파괴가 발생하였으며, 연단거리 변수의 실험 결과 매입깊이 이하인 경우 모두 콘크리트 파괴가 발생하였다. 동일한 변수의 실험 결과를 비교해 보았을 때 콘크리트 강도가 클수록 변위가 상대적으로 더 작게 나타났다.

• Geomechanics and Engineering
• /
• 제34권2호
• /
• pp.209-220
• /
• 2023

In this study, a series of three-dimensional numerical analyses were carried out to investigate the penetration performance of a dynamically installed Hall anchor. The advanced coupled Eulerian-Lagrangian (CEL) technique was adopted to accurately simulate the large soil deformation during the vertical penetration of a Hall anchor. In total, 52 numerical analyses were conducted to investigate the relationship between anchor penetration depth and the initial kinematic energy. Moreover, a sensitivity analysis was performed to investigate the effects of soil shear strength and soil type on the penetration mechanism of a drop anchor under self-weight. There is a monotonic increase in the penetration depth with an increasing anchor weight when the topsoil of the riverbed is not subjected to erosion. On the other hand, all the computed depths significantly increase when soil erosion is taken into consideration. This is mainly due to an enhanced initial kinematic energy from an increased dropping depth. Both depths increase exponentially with the initial kinematic energy. An enhanced shear strength can potentially increase the side resistance and end-bearing pressure around a drop anchor, thus significantly reducing the downward penetration of a hall anchor. Design charts are developed to directly estimate penetration depth and associated plastic zone due to dynamically installed anchor at arbitrary soil shear strength and anchor kinematic energy.