• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.5
• /
• pp.61-68
• /
• 2014

The energy efficiency of papermaking process becomes more significant because of various new regulation of the energy consumption and the green house gas emission. In this study, the effects of wood powder addition on the drainage and the drying efficiency of the OCC based paper products, linerboard, were deeply investigated for improving energy efficiency. The fractionation of wood powder depending on the size were conducted. The bigger size of wood powder resulted in the higher bulk and the higher drainage efficiency, but the lower paper strength. The drying efficiency were in detail evaluated depending on the drying process level. In the first section of drying process until the 80% solid level, there were no significant changes in the drying efficiency by the addition of wood powder. However, after the 80 % solid level, the drying efficiency was greatly improved by the addition of wood powder. Those results showed the addition of wood powder could greatly affect not only the drainage in forming and wet pressing but also the drying process.

• Resources Recycling
• /
• v.22 no.2
• /
• pp.18-21
• /
• 2013

In this study, surface modification of wood powder by atmospheric pressure plasma treatment was investigated. The composites were manufactured using wood powder and polypropylene(wood powder : PP = 55 wt% : 45 wt%). Atmospheric pressure plasma was treated as condition of 3KV, $17{\pm}1$KHz, 2 g/min. Helium was used as carrier gas and monomer such as hexamethyl-disiloxane(HMDSO) was used to modify surface property by plasma polymerization. The tensile strength of untreated waste wood powder(W3) and homogeneous wood powder(H3) were about 18.5 MPa, 21.5 MPa while the tensile strength of plasma treated waste wood powder(PW3) and homogeneous wood powder(PH3) were about 21.2 MPa, 23.4 MPa, respectively. And tensile strength of W3 and H3 were improved by 14.6% and 8.8%, respectively. From the results for mechanical property, morphological analysis, we obtained improved interfacial bonding of polypropylene and wood powder modified by plasma treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.6
• /
• pp.872-879
• /
• 2016

Demand of natural interior finishing material has been widely sprayed in nowadays because many weak people as children, pregnant women, and elder people are being struggled with sick house syndrome due to volatile organic compounds such as formaldehyde, toluene, benzene, etc. Our research group developed a no-added formaldehyde adhesive for wood-based panels from mainly rice powder and some additives in the previous study for abating sick house syndrome. Since the rice powder adhesive provides a good source of nutrients with microorganisms, it was suspected a susceptibility of the rice powder adhesive to fungal and sapstain attack. We evaluated anti-sapstain activity of the rice powder adhesives modified by adding wood preservatives. We modified the rice powder adhesive by adding three different types of anti-sapstain preservatives at three different concentrations to assess their anti-sapstin activity. The bonding strengths of the modified rice powder adhesives were still outstanding performance on all samples. Moreover, the plywood manufactured with the modified rice powder adhesive satisfied outdoor use requirement for ordinary plywood (KS F3101, Korean Standard). The results obtained showed that at least 3% of preservative should be added to the rice powder adhesive to obtain effective anti-sapstain activity.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.99-102
• /
• 2005

Plasma surface coating is applied to the wood powder to improve its bonding and dispersion with the polypropylene(PP). Some mechanical test results and visual inspection indicates the good compatibility between the wood powder and the PP, and relatively good interfacial adhesion between wood powder and PP matrix was seen. Also, this method is considered as a non-toxic process as compared to other direct chemical method.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.91-94
• /
• 2005

Polypropylene as a matrix has been used for wood polymer composites(WPC). In preparing WPC, the coupling agent, Polypropylene grafted Maleic Anhydride(PP-G-MA) was used in order to obtain a good interfacial bonding force between matrix and fillers and dispersion of wood powders. In this study, the effects of wood powder contents and water absorption on the mechanical properties were experimentally investigated. The tensile strength and flexural strength of composites reached its peak value when the wood powder content was around 60 wt%. However, the peak value of the impact was observed about 30 wt% of wood powder content. The tensile strength and flexural strength increase with increasing the wood power contents. But the impact strength decrease with increasing the wood powder contents. The slight change was observed with the water absorption in the WPC. The optimal condition of the compositions such as Anti-oxidant and UV stabilizers for the outdoor application was suggested in this research.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.6
• /
• pp.852-863
• /
• 2016

Wood-plastic composite (WPC) is a promising and sustainable material, and refers to a combination of wood and plastic along with some binding (adhesive) materials. In comparison to pure wood material, WPCs are in general have advantages of being cost effective, high durability, moisture resistance, and microbial resistance. The properties of WPCs come directly from the concentration of different components in composite; such as wood flour concentration directly affect mechanical and physical properties of WPCs. In this study, wood powder concentration in WPC was determined by Fourier transform near-infrared (FT-NIR) and Fourier transform infrared (FT-IR) spectroscopy. The reflectance spectra from WPC in both powdered and tableted form with five different concentrations of wood powder were collected and preprocessed to remove noise caused by several factors. To correlate the collected spectra with wood powder concentration, multivariate calibration method of partial least squares (PLS) was applied. During validation with an independent set of samples, good correlations with reference values were demonstrated for both FT-NIR and FT-IR data sets. In addition, high coefficient of determination (${R^2}_p$) and lower standard error of prediction (SEP) was yielded for tableted WPC than powdered WPC. The combination of FT-NIR and FT-IR spectral region was also studied. The results presented here showed that the use of both zones improved the determination accuracy for powdered WPC; however, no improvement in prediction result was achieved for tableted WPCs. The results obtained suggest that these spectroscopic techniques are a useful tool for fast and nondestructive determination of wood concentration in WPCs and have potential to replace conventional methods.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.1
• /
• pp.135-143
• /
• 2015

This study evaluated fuel properties of composite materials which were prepared by mixing a waste activated carbon from the used purifier filter with torrefied wood powder. Wood species of the raw material of torrefied wood powder are oak wood (Quercus serrata Thunb. ex Murray) and pine wood (Pinus densiflora Siebold & Zucc). And the treatment conditions used for this study were 300 s, 450 s, and 600 s at $200^{\circ}C$ for the wood roaster. Also, the mixing ratios are 5 : 95, 10 : 90, 15 : 85, 20 : 80, 40 : 60, 60 : 40 and 80 : 20 (waste activated carbon : torrefied wood powder). The fuel properties such as highly heating value (HHV), elementary analysis and ash content were evaluated. The results obtained are followings; 1. Despite the same treatment condition of wood roasting, pine wood has higher carbon contents than oak wood. Therefore, pine wood indicated the optimum carbonization at low temperature and short treatment times. 2. The gross calorific value and ash content increased as the mixing ratio of waste activated carbon increased. 3. Mixtures of the waste activated carbon and torrefied wood powder showed greater gross calorific value than those of the mixtures of waste activated carbon and the untreated wood powder. Also, the pine wood resulted in higher heating value that thaose of the oak wood. 4. When composite fuels that were composed waste activate carbon and wood powder are used, higher temperature conditions are required because the combustion is incomplete at $800^{\circ}C$ and 4 hours. 5. The increasing rate of the gross calorific value of mixtures of waste activated carbon and untreated wood powder is higher than does the mixtures of waste activated carbon and torrefied wood powder. Also, this phenomenon is more obvious for pine woods. Therefore, an optimal mixing ratio of waste activated carbon was determined to be between 5% and 10% (wt%). Also, this condition satisfied the requirement of the No.1 grade of wood pellet.

• Journal of Convergence for Information Technology
• /
• v.11 no.6
• /
• pp.188-197
• /
• 2021

In this study, the optimal conditions for hair dyeing using sappan wood (Caesalpinia sappan L.) powder were determined, and then the effect of chitosan treatment on the hair dyeing properties of sappan wood powder was investigated. Treatment of sappan wood powder and water with the ratio of 1:3 (w/w) at 40℃ for 60 minutes was found to be the most effective to hair dyeing. In addition, the pretreatment of low molecular weight (~30 kDa) chitosan at a concentration of 1% (w/w) prior to treatment with sappan wood powder effectively improved and maintained the hair dyeing properties of sappan wood. In conclusion, the low molecular weight chitosan is considered to be of great help as a mordant in improving the dyeing efficiency and retention of sappan wood powder in hair dyeing.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.5
• /
• pp.74-79
• /
• 2015

Wood powder is widely used in paperboard mills to increase bulk and reduce drying-energy consumption, but this material also deteriorates paper strength because it interferes with the bonds between fibers. Although there have been many studies done to improve the strength of paperboard containing wood powder, specific applications have not recently been observed in paperboard mills. In this study, we carried out a new approach for improving paperboard strength by developing a new organic filler with the ability to increase the bonds between fibers. The residue of tapioca starch was used as raw material to manufacture an organic filler. The functionalities, including bulk and strength, were evaluated by making handsheets containing either wood powder or tapioca organic filler, or a mixture of the two, and measuring their physical properties. The organic filler showed lower bulk improvement and higher paperboard strength than the wood powder. The mixture of tapioca organic filler and wood powder showed improved paperboard strength compared to wood powder alone. Therefore, tapioca residue can be used as a raw material to manufacture an organic filler for paperboard mills.

• Composites Research
• /
• v.30 no.2
• /
• pp.145-148
• /
• 2017

Wood powders were surface-modified by plasma-treating propylene to make them compatible with PP matrix in WPC(wood powder composite). The plasma treatment of propylene resulted in the deposition of an ultrathin hydrophobic film which had the chemical structure similar to that of polypropylene. Wood powder and polypropylene were mixed to pellets by twin screw extruder and then 50 wt% wood powder/PP composites were produced by an injection machine. Tensile strength and flexural strength were improved by 7.59% and 12.43% at the maximum respectively. SEM (Scanning Electron Microscopy) observation on the fracture surface revealed that the treatment improved the interfacial bonding and the mechanical properties of the composites.