Architectural research

  • 제26권1호
  • /
  • Pages.13-20
  • /
  • 2024
  • /
  • 1229-6163(pISSN)
  • /
  • 2383-5575(eISSN)
대한건축학회 (Architectural Institute of Korea)
권호 표지
DOI QR코드

DOI QR Code

Properties of Bubble used in Concrete ac cording to Change in Manufacturing Condition

  • Byoungil Kim (School of Architecture, Seoul National University of Science & Technology)
  • 투고 : 2023.12.03
  • 심사 : 2024.02.21
  • 발행 : 2024.03.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

This study is a research investigation into the properties of bubbles that affect the characteristics of foamed concrete during its production. The study examined the properties of bubbles based on the manufacturing conditions. To investigate these properties, the selected experimental factors included bead size, the length/diameter ratio of the bubble-generating tube, and compressed air. The experimental design used a design of experiments, and the test results were analyzed using analysis of variance. The foaming agent used to generate bubbles was AES (Alcohol Ethoxy Sulfate), and the method employed for bubble manufacture was the pre-foaming method. In the test results, a significant factor affecting the foaming rate of bubbles was the bead size; the highest foaming rate was observed when using 2mm beads. Bead size also primarily influenced the volume change of the aqueous solution, while other factors did not affect the foaming rate and volume change. None of the factors affected the change in bubble size, but compressed air was considered the main factor affecting bubble size and its change. The foaming rate and volume change of the aqueous solution showed a high correlation with each other. Spherical bubbles in the early stage eventually transformed into angular bubbles. Moreover, over time, it was observed that the bubble size increased.

키워드

참고문헌

  1. Ahn, H.J. (1997). Industrial Application of Surfactant and Forecast, Korean Chemical Industrial Institute, Research Thesis, 41~44.
  2. Choi, S.O., Gwak, G.S., Park, H.J., & Nam, G.D. (1999). Micelle Forming in Surfactant Aqueous Solution, Korean Industrial Chemistry Institute, 10(6): 876~880.
  3. Dow, C. (1991). Foam and Antiform theory, Data Sheet Number 22-0160A-01.
  4. Eisner, M.D., Jeelani, S.A.K., Bernhard, L, & Windhab. E.J. (2007). Stability of foams containing proteins, fat particles and nonionic surfactants, Chemical Engineering, 62(7): 1974~1987. https://doi.org/10.1016/j.ces.2006.12.056
  5. Gang, C. (2010). Development of Autoclave Lightweight Foam Concrete Using Bottom Ash and Waste Concrete Fine Powder, Gong-Ju University, Ph.D Thesis.
  6. Gwak, E.G., Gang, G.W., Gang, C., Gwun G.J., & Kim, J.M. (2004). Fundamental Researches on Foam Concrete Bubble Property, Korea Concrete Institute, 16(1): 681~683.
  7. Im, G., & Im J.S. (2006). Lightweight Foam Concrete Manufacture and Foam Machine Property Analysis, Engineering Thesis, Baejae University Engineer Institute No.8-1, 31~50.
  8. Jeelani, S.A.K., & Hartland, S. (1994). Effect of interfacial mobility on thin-film drainage, Journal of Colloid and Interface Science ,164(2): 296~308. https://doi.org/10.1006/jcis.1994.1171
  9. Kang, S.L., Kim, G.Y., & Gwak, H.Y. (2004). Bubble Formation in Polumer Solution, Polymer Science and Technology, Polymer, 28(1): 51~58.
  10. Kasai, Y., & Kobayashi, M. (1993). (revised edition) Cement. Admixture materials for concrete, Gijutsu Shoin, 433~437. Kim, D.H., Jang, S.G., & Park, S.W. (2000). Surfactant, Analysis Science, 13(2): 27~48.
  11. Kim, H.W., & Im, K.H. (2001). Critical Micelle Concentration and Temperature Correlation in Surfactant Aqueous Solution, Joong-Ang University Future New Technology Institute, 123~133.
  12. Kim, J.M., Gwak, E.G., Oh, G.J., & Gang, C. (2010). Bubble Property Depending on Concrete foam Body Type and Concentration, Korea Concrete Institute, 23(2): 151~158.
  13. Korea Institute of Science and Technology (KIST), (2002). 2002 Chemistry, Chemical Technology II.
  14. Kroezen, A.B.J., & Wassink, J. G. (1987). Bubble size distribution and energy dissipation in foam mixers, Journal of the Society of Dyers and Colourists, 103(11): 386~394. https://doi.org/10.1111/j.1478-4408.1987.tb01090.x
  15. Lee, G.S. (2005). Development of Non-Contraction Vegetable Foam Body for Crack Prevention in Lightweight Foam Concrete, Baejae University, Materials Engineering Department.
  16. Noh, J.S., Cho, H.Y., & Hong, S.S. (1994). Cement Concrete admixture Surfactant Research Trend, Chemical Industry and Technology, 12(5): 397~405.
  17. Park, J.G., & Im, J.R. (1995). Laboratory Research on Surfactant Aqueous Solution Bubble Force and Foam Stability, Korea Materials Institute, 32(3): 230~236.
  18. Ramanurthy, K., Nambiar, E.K.K., & Gandhi, I.S.R. (2009). A Classification of Studies on Properties of Foam Concrete, Cement & Concrete Composites, 31(6): 388~396. https://doi.org/10.1016/j.cemconcomp.2009.04.006
  19. Richard, J. F. (2006). Chemistry and Technology of Surfactant, Blackwell Publishing, 76~81.