권호 표지

한국진공학회지 (Journal of the Korean Vacuum Society) (Journal of the Korean Vacuum Society)

한국진공학회 (The Korean Vacuum Society)

  • 격월간
  • /
  • 1225-8822(pISSN)

과학기술표준분류

  • 물리학 ＞ 광학

Aim & Scope

ASCT has six major fields: vacuum technology, surface and interface science, plasma and display, semiconductors and thin films, nano and biointerface, and energy technology. ASCT accepts research paper, review paper, rapid communications, brief reports and technical notes. It publishes articles immediately after the review process if manuscript is determined as acceptance. The official title of the journal is Applied Science and Convergence Technology and its abbreviation is ASCT.

KSCI SCOPUS

제8권3A호

  1. 남창우;홍진표;김채옥 181
    PDF
    The diffusion of oxygen atoms on tungsten (110) surface is studied by comparison of experiment results and recent calculations. It has been suggested that the thermodynamic factor which is inversely proportional to be compressibility has strong temperature dependence which may cause non-Arrhenius behavior of diffusion coefficient. Recent experiments, however, indicate effectively no temperature dependence of this factor and support the view that non-Arrhenius behavior originates from the dynamic factor rather than the thermodynamic factor. Discrepancies in coverage dependence of physical quantities between theory and experiment are discussed.
  2. 이선우;박수홍;이덕출 187
    PDF
    In this study, PVDF thin films which show the excellent piezoelectricity and pyroelectricity, are prepared by PVD (physical vapor deposition) method, and thir electrical conduction phenomena for analyses of the electrical conduction mechanism and TSC (Thermally Stimulated Current) for identification of the behavior of conductive carriers are investigated. As a result of FT-IR(Fourier Transform Infrared Spectroscopy) spectra, the crystalline phase transforms $\alpha$ type into $\beta$ type with increasing electric field. From XRD (X-Ray diffraction) analyses patterns, the degree of crystallinity increases from 49.8% to 67%, as the substrate temperature increases from $30^{\circ}C$ to $80^{\circ}C$. As a result of electrical conduction phenomena, the electrical conduction mechanism of PVDF thin films is identified as ionic conduction mechanism. From TSC analyses, there are three peaks as P1, P2, P3 with increasing temperature, and with increasing substrate temperature, the peak temperature of TSC increases and the peak intensity of TSC decreases.
  3. 박수홍;이선우;이희규 194
    PDF
    In this paper studied was the piezoelectric properties of the $\beta$-PVDF organic thin films prepared by physical vapour deposition method. The molecular orientation of organic thin films was controlled by the application of an electric field and variation of substrate temperature during the evaporation process. Optimum conditions of manufacturing $\beta$-PVDF organic thin film by physical vapor deposition method is to keep at the substrate temperature of $80^{\circ}C$, at the applied electric field of 142.8 kV/cm. The voltage output coefficient increased from 1.39 to 7.04V increasing the force moment.
  4. 이상운;윤천호;박정일;박광자 201
    PDF
    Transparent and conduction tin oxide films have been deposited on glass substrates employing the low pressure chemical vapor deposition technique. Tetramethyltin, 1, 1, 1, 2-tetrafluoroethane, and pure oxygen or ozone-containing oxygen were used as the precursor, dopant and oxidant, respectively. In order to examine the role of ozone in the low pressure chemical vapor deposition of tin oxide films, deposition rate, and electrical and optical properties of tin oxide films deposited using ozone-containing oxygen were compared with those using pure oxygen. Tetramethyltin and 1, 1, 1, 2-tetrafluoroethane were chemically activated by thermally initiated decomposition of ozone. Using ozone-containing oxygen under otherwise identical deposition conditions, we succeeded in preparing tin oxide films f better quality at higher deposition rate.
  5. 장영근;김현수;최훈상;오대곤;최인훈 207
    PDF
    Undoped InP epilayers with high purity were grown by using $In/PCl_3/H_2$ chloride vapor phase epitaxy. It was found that the growth of InP homoepitaxial layer is optimized at the growth temperature of $630^{\circ}C$ and at the $PCl_3$ molar fraction of $1.2\times10^{-2}$. The carrier concentration of InP epilayer was less than $10^{14} {cm}^{-3}$ from the low temperature (11K) photoluminescence measurement. Growth behavior of undoped InP current blocking layer on reactive ion-etched (RIE) mesas has been investigated for the realization of 1.55 $\mu \textrm m$buried-heterostructure laser diode (BH LD), using chloride vapor phase epitaxy. On the base of InP homoepitaxy, InP current blocking layers were grown at the growth temperatures ranging from $620^{\circ}C$ to $640^{\circ}C$. Almost planar grown surfaces without edge overgrowth were achieved as the growth temperature increased. It implied that higher temperature enhanced the surface diffusion of the growth species on the {111} B planes and suppressed edge overgrowth.
  6. 허재혁;채동훈;박성렬;이동렬;박수현;정윤희;전인준;김동언;이기봉 213
    PDF
    Fe/MnO multilayers with different bilayer thicknesses were grown by pulsed laser deposition method. Grazing incidence X-ray reflectivity results showed obvious multilayer Bragg peaks implying highly layered samples and, through their analysis, some structural parameters were quantiatively estimated. From the X-ray diffraction peak corresponding to MnO(111), Mn-oxide turned out to be dominantly MnO. To characterize the magnetic properties of $Mn^{+2}$, XMCD were carried out. Magnetic moments of MnO near interfaces were ordered in the opposite direction to those of Fe.
  7. 정윤하;강성관;김은하;고대홍;조만호;황정남 218
    PDF
    We investigated the interfacial reactions between the $Y_2O_3$ film deposited by ICB processing and p-type (100) Si substrates upon annealing treatments in $O_2$ and Ar gas ambients. we also investigated the evolution of surface morphology of ICB deposited $Y_2O_3$ films upon annealing treatments. We observed that the root-mean-square(RMS) value of surface roughness measured by AFM increased with annealing time at $800^{\circ}C$ in $O_2$ ambient, while the change of surface roughness was not observed in Ar ambient. We also found the growth of $SiO_2$ layer and the formation of yttium silicate layer. From the capacitance values $(C_{acc})$ measured by C-V measurements, the relative didldctric constant of $Y_2O_3$ film in metal-insulator-semiconductor(MIS) structure was estimated to be about 9.
  8. 연대중;권용욱;박주동;오태성 224
    PDF
    $SrBi_{2x}Ta_2O_9$ (SBT) thin films were prepared on platinized silicon substrates by MOD process, and their ferroelectric and leakage current characteristics were investigated. The grain size of the MOD derived SBT films increased with increasing the BI/Ta mole ration. Although the SBT films with x of 0.8~1.2 were composed of the equiaxed grains, the elongated grains were also observed for the SBT films with x of 1.4 and 1.6. The SBT film with x of 1.2 exhibited the optimum ferroelectric properties of 2PR : 9.79 $\muC/\textrm{cm}^2$ and Ec : 24.2kV/cm at applied voltage of 5V. The leakage current density of the SBT films increased with increasing the BI/Ta mole ratio. With post annealing process, 2Pr and $E_c$of the SBT film with x of 1.2 increases 11.3 $\muC/\textrm{cm}^2$ and 39.6kV/cm, respectively. decrement of the leakage current density by post annealing process increased remarkably with increasing the Bi/ta mole ratio, and the SBT film with x=1.6 exhibited the lowest leakage current density after post annealing process.
  9. 박주동;권용욱;연대중;오태성 231
    PDF
    $SrBi_{22.4}Ta_2O_9$ (SBT) thin films of 70~150 nm thickness were prepared on platinized silicon substrates by Liquid Source Misted Chemical Deposition (LSMCD) process, and their microstructure, feroelectric and leakage current characteristics were investigated. By annealing at $800^{\circ}C$ for 1 hour in oxygen ambient, SBT films were fully crystallized to the Bi layered perovskite structure without preferred orientation. The grain size of the LSMCD- derived SBT films was about 100nm, and was not varied with the film thickness. $2P_r$ and $E_c$ of the SBT films increased with decreasing the film thickness, and the 70nm-thick SBT film exhibited $2P_r$ of 17.8 $\mu$C/$\textrm{cm}^2$ and $E_c$ of 74kV/cm at applied voltage of 5V. Within the film thickness range of 70~150nm, the relative dielectric permittivity of the LSMCD-derived SBT film decreased with decreasing the film thickness. Leakage current densities lower than $10^{-7}\textrm{A/cm}^2$ at 5V were observed in the SBT films thicker than 125nm.
  10. 권용욱;박주동;연대중;오태성 238
    PDF
    Pt/SBT/Pt capacitors were fabricated using the MOD-derived $SrBi_{2x}Ta_2O_9$ (SBT) films and their ferroelectic and leakage current characteristics were investigated with post annealing at 400~$800^{\circ}C$. Although the MOD-derived SBT film exhibited the hysteresis loop typical for the leaky film, the well-saturated ferroelectric hysteresis loop could be obtained by post annealing the Pt/SBT/Pt capacitors at $550^{\circ}C$~$800^{\circ}C$. The remanent polarization $2P_r$ of the SBT film exhibited a maximum value of 9.72$\mu\textrm{cm}^2$ with post annealing at $600^{\circ}C$, and then decreased with increasing the post annealing temperature above $600^{\circ}C$. The MOD-derived SBT films exhibited the high leakage current density of ~$10^{-3} \textrm{A/cm}^2$ at 75kV/cm. With post annealing the Pt/SBT/Pt capacitor at 600~$800^{\circ}C$, however, the leakage current density decreased remarkably to less than $10^{-6}\textrm{A/cm}^2$ at 75kV/cm.
  11. 김동식;정관수 245
    PDF
    Recently low resistance of gate line or data line is required for large screen size TFT-LCD panels. As a result, lower resistance Al-alloy is currently reviewed extensively and the resistivity is required smaller than 10$\mu\Omega$cm. In this paper, Al-Nd and Al-Zr thin film were deposited on glass substrated by D.C. magnetron sputtering system under various condition. Its properties were characterized by SEM, AFM, XRD and 4-point-probe. The optimal condition was $120^{\circ}C$, 125W, 0.4Pa, 30sccm (Ar) and $350^{\circ}C$, 20min. annealing. At that condition the resistivity of Al-Zr(0.9%wt.) is about 4$\mu\Omega$cm.
  12. 이종현;이정환;최시영 249
    PDF
    Deposition characteristics of Cu thin films using Ar carrier gas and $H_2$ processing gas at various working pressures and substrate temperatures were investigated. Also, effects of $H_2$ pretreatment using plasma at $200^{\circ}C$ of substrate temperature and 0.6 Torr of chamber pressure were stdied. Cu thin films were deposited on TiN/Si substrate at working pressure of 0.5~1.5 Torr, substrate temperatures of 140~$240^{\circ}C$ with (hface)Cu(tmvs). Substrates were pretreated by $H_2$ plasma, and Cu films deposited in situ using twofold shower head. The purity, electrical resistivity, thickness, surface morphology, optical properties of the deposited Cu films were measured b the AES, four point probe, stylus profiler, SEM,. and the uv-visible spectrophotometer. This study suggests that $H_2$ plasma is an effective method for enhancing deposition rate and for producing high quality copper thin films.